Homelite UT49102 Operation, AssemblING the wheels, Before usING the LOG Splitter

Page 11

ASSEMBLY

assemblING THE wheels

See Figure 3.

To attach the wheels to the base:

nLocate the axle assembly; remove the hitch pin from the axle.

nLift the machine slightly and slip the axle into the wheel hole.

nNext, slide the washer onto the axle. Still lifting the machine, slide the axle/wheel/washer combination into

the wheel mounting hole in the machine base as shown in figure 3.

nSlide the washer onto the axle. Push the hitch pin into the hole on the end of the axle to secure the wheel assembly.

NOTE: The hitch pin should be pushed into the axle until the center of the pin rests on top of the axle.

nRepeat with the second wheel assembly.

OPERATION

WARNING:

Do not allow familiarity with tools to make you care- less. Remember that a careless fraction of a second is sufficient to inflict serious injury.

WARNING:

Always wear safety goggles or safety glasses with side shields when operating this tool. Failure to do so could result in objects being thrown into your eyes resulting in possible serious injury.

WARNING:

Do not use any attachments or accessories not recommended by the manufacturer of this tool. The use of attachments or accessories not recommended can result in serious personal injury.

BEFORE usING THE LOG SPLITTER

See Figures 4 - 5.

Never operate the log splitter until the bleed screw has been slightly loosened (one to two full turns). Air flow through the bleed screw should be detectable once the log splitter is started. If no air flow is de- tected, loosen the screw until the air flow can be felt.

Air must flow in and out of the oil tank during operation to prevent the seals in the hydraulic system from rupturing.

This tool is designed for home use only. Never split logs larger than 10 in. diameter or 20-1/2 in. long. Some types of wood are harder to split than others. If the log splitter is having trouble splitting a log, never continue to try for longer than five seconds.

Always check the oil level before you start the log splitter.

To check the oil level:

nUnplug the log splitter.

nUsing the lift handle, stand the log splitter on the end with the wheels (see figure 12).

nUsing an 8 mm hex key, remove the oil drain bolt and wipe the dipstick clean.

nWipe the dipstick clean then reinsert it back into the oil tank.

nRemove the dipstick and check to see if the oil level is between the first and second groove on the dipstick.

nIf there is not enough oil in the oil tank, add oil until the proper level is reached.

nIf there is the proper amount of oil in the oil tank, wipe the dipstick clean then replace it in the oil tank and tighten the oil drain bolt securely.

NOTE: See “Replacing Hydraulic Oil” in the Maintenance section for recommended oil or equivalents.

STARTING THE LOG SPLITTER

See Figures 6 - 7.

nOperator should be positioned at the rear of the log split- ter as shown in figure 7.

nPlace the left hand on the hydraulic control lever and the right hand on the on/off switch.

nPush down and hold the on/off switch.

nWhile continuing to hold down the on/off switch, push down and hold the hydraulic control lever.

NOTE: Both hands are required to start this product. The combination of both steps starts the ram which pushes the log into the wedge.

9 — English

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Save this Manual for Future Reference OPERATOR’S ManualTable of Contents Page Iii Read ALL Instructions General Safety Rules Circuit Capacity and Fuses  Useonlyyour Handtooperatethelogsplitter ControlsSymbol Name DESIGNATION/EXPLANATION SymbolsAuthorized Service Center for repair. When servic ServiceSymbol Signal Meaning Electrical Connection Speed and WiringCord Length Wire Size A.W.G Extension CordsAssembly FeaturesStarting the LOG Splitter Before usING the LOG SplitterOperation AssemblING the wheelsReplacing Hydraulic OIL MaintenanceGeneral Maintenance LubricationSharpening the Wedge TroubleshootingProblem Possible Cause Solution Maintenance sectionLimited Warranty Statement WarrantyAVERTISSEMENT  Règles DE Sécurité Générales Capacité DU Circuit ET Fusibles Règles DE Sécurité ParticulièresSymbole NOM Désignation / Explication SymbolesAVERTISSEMENT  DépannageInstructions de mise à la terre Cordons prolongateursConnexion électrique Vitesse ET CâblageAssemblage CaractéristiquesMise EN Marche DE LA Fendeuse UtilisationFixation DE Roues Avant DE Mettre LA Fendeuse EN MarcheEntretien Pour verrouiller la fendeuse de bûches Problème Cause possible SolutionDépannage Affûtage DU CoinGarantie LEA Todas LAS Instrucciones Reglas DE Seguridad Generales Capacidad DEL Circuito Y Fusibles Reglas DE Seguridad EspecíficasSímbolo Nombre DENOMINACIÓN/EXPLICACIÓN SímbolosServicio PeligroAdvertencia PrecauciónInstrucciones de conexión a tierra Cordones de extensiónConexión eléctrica Velocidad Y CableadoArmado CaracterísticasPara revisar el nivel de aceite FuncionamientoAcoplamiento de rueda Antes DE Encender LA Partidora DE TroncosReemplazo DEL Aceite Hidráulico MantenimientoMantenimiento General LubricaciónPara trabar la partidora de troncos Solución DE ProblemasProblema Causa posible Solución Afilado DE LA CuñaDeclaración DE LA Garantía Limitada GarantíaNotas Notas Notas Ut49102 Manuel D’UTILISATION Manual DEL Operador

UT49102 specifications

The Homelite UT49102 is a versatile and efficient gas-powered string trimmer designed to tackle a wide variety of lawn care tasks, making it a popular choice among homeowners and professional landscapers alike. With its powerful engine, user-friendly design, and advanced features, the UT49102 has gained a reputation for delivering reliable performance and ease of use, transforming the way users maintain their outdoor spaces.

One of the standout features of the Homelite UT49102 is its powerful 26cc, 2-cycle engine that provides ample strength for cutting through thick grass and weeds. This engine is designed for reliability and efficiency, ensuring that users can complete their trimming tasks quickly and effectively. The lightweight construction of the trimmer makes it easy to handle and maneuver, allowing users to navigate around obstacles and reach tight spaces without fatigue.

In terms of technology, the UT49102 incorporates a unique automatic prime feature that simplifies the starting process. This system helps to eliminate the frustration that often comes with starting a gas-powered engine, allowing users to get to work faster. Additionally, the trimmer features a bump feed head that ensures a constant supply of nylon line, so users can easily advance the line with a gentle tap on the ground.

The trimmer is equipped with a dual line cutting system, which enhances its efficiency by allowing for a wider cutting path. This feature helps to reduce the time spent trimming and promotes superior cutting performance. The ergonomically designed handle further enhances comfort during extended use, as it reduces strain on the arms and back.

Durability is another key characteristic of the Homelite UT49102. It features a robust construction that can withstand the rigors of regular use, ensuring that users can rely on it for their lawn care needs. The trimmer is also designed with easy access to parts for maintenance, making it simple for users to keep the machine in optimal condition.

Overall, the Homelite UT49102 gas-powered string trimmer combines power, efficiency, and user-friendly features. Its lightweight design, advanced technology, and durability make it an excellent choice for anyone looking to maintain a beautiful lawn. Whether you are a homeowner or a landscaping professional, the UT49102 is equipped to help you achieve a well-manicured yard with ease and precision.
Top Page Image Contents