Great Dane GBKW2561S Adjusting Mower Deck Cutting Height, Adjusting Mower Deck Anti-Scalp Wheels

Page 15

OPERATING

4.Push ROPS into upright position.

5.Install drilled pin (B) into holes on left and right side of ROPS, and secure in place with spring pins (A).

6.Check the ROPS bolt torque if the ROPS is loose.

Lowering ROPS

CAUTION: Avoid injury! Use roll-over protection system (ROPS) in lowered position only when low clearance operation is necessary.

•Do not use seat belt when ROPS is in lowered position.

•Do not operate machine on slope with ROPS in folded position.

•Raise ROPS and fasten seat belt as soon as conditions permit.

1.Park machine safely. (See Parking Safely in the SAFETY section). 2.Remove spring pin (A) from drilled pin (B) on left and right side of ROPS. 3.Remove drilled pin from left and right side of ROPS.

4.Pull ROPS rearward to lower.

5.Install drilled pins and spring pins back into hole in ROPS to secure in place.

Adjusting Mower Deck Cutting Height

CAUTION: Avoid injury! Rotating blades are dangerous and can cut fingers and toes. Stop engine, lock the park brake, and wait for blade to stop rotating before adjusting cutting height.

Cutting height can be adjusted from approximately 25-125 mm (1-5 in.). Each hole adjusts the height-of-cut (HOC) in approximately 12 mm (1/2 in.) increments.

The deck can also be raised and locked in a transport position, to provide maximum ground clearance when moving the machine from one area to another.

1.Park machine safely. (See Parking Safely in the SAFETY section.)

2.Move the mower deck lift lever (A) to the transport position (D).

3.Position the HOC adjustment pin (C) in the proper hole for the desired height-of-cut.

4.Pull back and hold the mower deck lift lever (A) and release the transport position lock lever (B).

5.Allow the mower deck lift lever (A) to rest against the HOC adjustment pin (C).

Adjusting Mower Deck Anti-Scalp Wheels

1.Park machine safely. (See Parking Safely in the SAFETY section.)

CAUTION: Avoid injury! Fingers and loose clothing can get caught in rotating parts. Do not operate machine without all mower deck belt shields installed.

NOTE: The flattest cut can be achieved by having all anti-scalp wheels adjusted off the ground. Check anti-scalp wheel adjustments each time the mower deck cutting height is changed.

It is recommended that all anti-scalp wheels be kept off the ground to minimize scuffing.

2.Inflate tires to correct pressure.

3.Adjust mower deck to desired cutting height.

Operating - 13

Page 14 Page 16
Image 15
Page 14 Page 16
Contents OPERATOR’S Manual Page Introduction IntroductionProduct Identification Safety Labels Safety LabelsUnderstanding The Machine Safety Labels Safety Labels Avoid Crushing Safety SafetyUsing a Spark Arrestor Checking Mowing Area Parking SafelyRotating Blades are Dangerous Use Seat Belt Properly Keep Rops Installed ProperlyProtect Children Avoid TippingDriving Safely on Public Roads Maintenance and StorageKeep Riders Off Avoid High Pressure FluidsTire Safety Prevent FiresHandling Fuel Safely Handling Waste Product and Chemicals Daily Operating ChecklistOperating OperatingRaising and Lowering Operator Seat Operator Station ControlsMiscellaneous Controls Mounting and Dismounting Machine SafelyAdjusting Seat Using Seat BeltRaising and Lowering Rops Adjusting Mower Deck Anti-Scalp Wheels Adjusting Mower Deck Cutting HeightTesting Neutral Start Switch Testing Safety SystemsTesting PTO Switch Testing Park Brake SwitchProcedure Testing Seat SwitchTesting the Park Brake Using the Park BrakeUsing the Hourmeter Using the Key SwitchUsing the PTO Using the Throttle LeverDisengage Choke Using the ChokeUsing the Motion Control Levers Engage ChokeGentle Right Turn ForwardReverse Gentle Left TurnStarting the Engine Sharp Left TurnSharp Right Turn Mowing Tips Engaging MowerStopping the Engine Transporting MachineService Intervals Service IntervalsSpray Lubricant Service LubricationService Lubrication GreaseAvoid Fumes Service EngineService Engine Engine Warranty Maintenance StatementChecking Engine Oil Level Changing Engine Oil and FilterOil Capacity With Filter Dry Replacing Fuel Filter Cleaning Engine Air Intake Screen and FanChecking and Cleaning Air Filter Elements Adjusting CarburetorChecking Hydraulic Oil Level Service TransmissionService Transmission Hydraulic OilCleaning Hydraulic Pump Cooling Fins Removing and Installing Traction Drive BeltChecking and Adjusting Motion Control Linkages Neutral Creep Adjustment Maximum Speed Drift AdjustmentCheck Maximum Speed Drift Service Transmission Hydraulic System Hose Routing Service Steering & Brakes Service Steering & BrakesHydraulic System Schematic Servicing Front Caster Wheel Roller Bearings Chariot Removing and Installing Front Caster WheelsAdjusting Front Caster Spindle Bearing InstallingHeight Adjustment Procedure Servicing Caster Spindle BearingsCheck Alignment Removing and Installing Mower Deck Foot Plate Service MowerService Mower Adjusting Park BrakeLeveling Mower Deck Removing and Installing Mower Deck Belt ShieldsAdjusting Level Side-to-Side Picture Note Discharge chute raised for photo clarityChecking Level Front-to-Rear Checking and Adjusting Cutting Height Adjusting Deck Lift Assist Spring TensionChecking and Adjusting Mower Deck Drive Belt Tension Checking and Replacing Mower Blades Removing and Installing Mower Deck Drive BeltReplacing Mower Blades Sharpening BladesBalancing Blades Replacing Mower Spindle BearingsRemoving and Installing the Battery Service ElectricalService Electrical Service the Battery SafelyBurnishing the PTO Clutch Cleaning Battery and TerminalsUsing Booster Battery Replacing FuseWiring Schematic Service Miscellaneous Service MiscellaneousCleaning and Repairing Metal Surfaces TroubleshootingTroubleshooting Cleaning and Repairing Plastic SurfacesEngine Electrical SystemCheck Mower Deck MachinePark Brake SteeringAssembly StorageStorage Check Fluid Levels AssemblyInstall Motion Control Levers Install SeatInstall Rops Specifications SpecificationsGetting Quality Service Getting Quality ServiceEngine and Related Components Kawasaki Ref. No Description Qty Remarks Engine and Related Components Kohler 27 HP Hose OIL Drain Fuel Delivery System Components Over the LAP Control Assembly Electrical and Related Components Fuse Console and Control Assembly Console Hydrostatic Drive System Components Ref.No Description Qty Remarks Traction Drive and Brakes Pivot Hydraulic Schematic Seat Components Frame Assembly Frame Front Caster Assembly Yoke Caster TCA16051 RopsPage Spindle Assembly Ref. No Description Qty Remarks Deck Lift Assembly Bearing CAP 52 Cutting Deck Mower Deck Cutting Deck GDA10077 Labels Cutting Deck Labels Labels

GBKW2561S, GBKH2752S, GBKW2552S, GBKH2761S specifications

The Great Dane GBKH2761S, GBKW2552S, GBKH2752S, and GBKW2561S are a series of powerful and versatile washing machines designed to meet the needs of modern households. These models stand out for their innovative features, advanced technologies, and user-friendly characteristics, making laundry more efficient and effective.

One of the main features of the Great Dane washing machines is their large capacity, which allows users to wash a significant amount of laundry in one go. This is particularly beneficial for families or individuals with substantial laundry needs, as it reduces the number of loads required and saves valuable time. Additionally, the machines come equipped with a variety of wash programs tailored to different fabric types and soiling levels, ensuring optimal results for every load.

In terms of technologies, these models incorporate intelligent sensors that automatically adjust wash cycles based on the load size and fabric type. This not only enhances cleaning performance but also improves energy efficiency, as the machines consume only the necessary amount of water and electricity. The Great Dane GBKH2761S and GBKW2561S models feature inverter motors that provide quieter operation and greater reliability, translating to longer-lasting performance.

Another standout characteristic of the Great Dane washing machines is their user-friendly interface. The intuitive control panel allows users to select programs and settings easily, while the digital display provides real-time information on the wash cycle. Furthermore, many models are equipped with a delay start feature, offering flexibility for scheduling laundry around busy lifestyles.

In terms of design, the Great Dane series incorporates sleek aesthetics with durable construction, ensuring they not only perform well but also complement modern home interiors. The energy-efficient ratings of these machines make them environmentally friendly choices, helping users reduce their carbon footprint while maintaining high cleaning standards.

Overall, the Great Dane GBKH2761S, GBKW2552S, GBKH2752S, and GBKW2561S represent a blend of cutting-edge technology, capacity, efficiency, and user convenience, making them an ideal choice for consumers seeking reliable and effective washing solutions.
Top Page Image Contents