Great Dane GBKH2761S manual Testing Safety Systems, Testing PTO Switch, Testing Park Brake Switch

Page 16

OPERATING

NOTE: The rear anti-scalp wheels are located under the rear of the mower deck.

4.Adjust anti-scalp wheel (A) to one of two positions (B).

•Remove screw (C), nut and washer.

•Adjust wheel up or down so it is approximately 6-13 mm (1/4-1/2 in.) above mowing surface.

5.Install wheel with attaching hardware. 6.Adjust all wheels to same height.

Testing Safety Systems

CAUTION: Avoid injury! Engine exhaust fumes contain carbon monoxide and can cause serious illness or death.

Move the machine to an outside area before running the engine.Do not run an engine in an enclosed area without adequate ventilation.•

•Connect a pipe extension to the engine exhaust pipe to direct the exhaust fumes out of the area.

•Allow fresh outside air into the work area to clear the exhaust fumes out.

The safety systems installed on your machine should be checked before each machine use. Be sure you have read the machine operator manual and are completely familiar with the operation of the machine before performing these safety system checks.

Use the following checkout procedures to check for normal operation of machine.

If there is a malfunction during one of these procedures, do not operate machine. See your authorized dealer for service.

Perform these tests in a clear open area. Keep bystanders away.

Testing Safety Systems

CAUTION: Avoid injury! Engine exhaust fumes contain carbon monoxide and can cause serious illness or death.

Move the machine to an outside area before running the engine.Do not run an engine in an enclosed area without adequate ventilation.•

•Connect a pipe extension to the engine exhaust pipe to direct the exhaust fumes out of the area.

•Allow fresh outside air into the work area to clear the exhaust fumes out.

The safety systems installed on your machine should be checked before each machine use. Be sure you have read the machine operator manual and are completely familiar with the operation of the machine before performing these safety system checks.

Use the following checkout procedures to check for normal operation of machine.

If there is a malfunction during one of these procedures, do not operate machine. See your authorized dealer for service.

Perform these tests in a clear open area. Keep bystanders away.

Testing PTO Switch

1.Sit on the operator seat with the motion control levers in the neutral detent position (standard levers) or neutral lock position (optional “over the lap” levers).

2.Lock the park brake.

3.Pull PTO knob up to engage.

4.Turn key switch to the start position.

Result: The engine must not crank.

Testing Park Brake Switch

1.Sit on the operator seat with the motion control levers in the neutral detent position (standard levers) or neutral lock position (optional “over the lap” levers).

2.Push PTO knob down to disengage.

3.Unlock the park brake.

4.Turn key switch to the start position.

Result: The engine must not crank.

Testing Neutral Start Switch

NOTE: Repeat this test three times, with the motion control levers in the following positions:

•Right side motion control lever inward.

•Left side motion control lever inward.

•Both motion control levers inward.

1.Move motion control lever(s) out of the neutral detent position (standard levers) or neutral lock position (optional “over the lap” levers).

2.Lock the park brake.

3.Push PTO knob down to disengage.

4.Turn key switch to the start position.

Result: The engine must not crank.

Operating - 14

Page 15 Page 17
Image 16
Page 15 Page 17
Contents OPERATOR’S Manual Page Introduction IntroductionProduct Identification Safety Labels Safety LabelsUnderstanding The Machine Safety Labels Safety Labels Avoid Crushing Safety SafetyChecking Mowing Area Parking Safely Using a Spark ArrestorRotating Blades are Dangerous Keep Rops Installed Properly Protect ChildrenAvoid Tipping Use Seat Belt ProperlyMaintenance and Storage Keep Riders OffAvoid High Pressure Fluids Driving Safely on Public RoadsPrevent Fires Tire SafetyHandling Fuel Safely Daily Operating Checklist OperatingOperating Handling Waste Product and ChemicalsOperator Station Controls Miscellaneous ControlsMounting and Dismounting Machine Safely Raising and Lowering Operator SeatUsing Seat Belt Adjusting SeatRaising and Lowering Rops Adjusting Mower Deck Cutting Height Adjusting Mower Deck Anti-Scalp WheelsTesting Safety Systems Testing PTO SwitchTesting Park Brake Switch Testing Neutral Start SwitchTesting Seat Switch Testing the Park BrakeUsing the Park Brake ProcedureUsing the Key Switch Using the PTOUsing the Throttle Lever Using the HourmeterUsing the Choke Using the Motion Control LeversEngage Choke Disengage ChokeForward ReverseGentle Left Turn Gentle Right TurnSharp Left Turn Starting the EngineSharp Right Turn Engaging Mower Stopping the EngineTransporting Machine Mowing TipsService Intervals Service IntervalsService Lubrication Service LubricationGrease Spray LubricantService Engine Service EngineEngine Warranty Maintenance Statement Avoid FumesChanging Engine Oil and Filter Checking Engine Oil LevelOil Capacity With Filter Dry Cleaning Engine Air Intake Screen and Fan Checking and Cleaning Air Filter ElementsAdjusting Carburetor Replacing Fuel FilterService Transmission Service TransmissionHydraulic Oil Checking Hydraulic Oil LevelRemoving and Installing Traction Drive Belt Cleaning Hydraulic Pump Cooling FinsChecking and Adjusting Motion Control Linkages Maximum Speed Drift Adjustment Neutral Creep AdjustmentCheck Maximum Speed Drift Service Transmission Hydraulic System Hose Routing Service Steering & Brakes Service Steering & BrakesHydraulic System Schematic Removing and Installing Front Caster Wheels Adjusting Front Caster Spindle BearingInstalling Servicing Front Caster Wheel Roller Bearings ChariotServicing Caster Spindle Bearings Height Adjustment ProcedureCheck Alignment Service Mower Service MowerAdjusting Park Brake Removing and Installing Mower Deck Foot PlateRemoving and Installing Mower Deck Belt Shields Leveling Mower DeckPicture Note Discharge chute raised for photo clarity Adjusting Level Side-to-SideChecking Level Front-to-Rear Adjusting Deck Lift Assist Spring Tension Checking and Adjusting Cutting HeightChecking and Adjusting Mower Deck Drive Belt Tension Removing and Installing Mower Deck Drive Belt Checking and Replacing Mower BladesSharpening Blades Balancing BladesReplacing Mower Spindle Bearings Replacing Mower BladesService Electrical Service ElectricalService the Battery Safely Removing and Installing the BatteryCleaning Battery and Terminals Using Booster BatteryReplacing Fuse Burnishing the PTO ClutchWiring Schematic Service Miscellaneous Service MiscellaneousTroubleshooting TroubleshootingCleaning and Repairing Plastic Surfaces Cleaning and Repairing Metal SurfacesElectrical System EngineCheck Machine Park BrakeSteering Mower DeckStorage AssemblyStorage Assembly Install Motion Control LeversInstall Seat Check Fluid LevelsInstall Rops Specifications SpecificationsGetting Quality Service Getting Quality ServiceEngine and Related Components Kawasaki Ref. No Description Qty Remarks Engine and Related Components Kohler 27 HP Hose OIL Drain Fuel Delivery System Components Over the LAP Control Assembly Electrical and Related Components Fuse Console and Control Assembly Console Hydrostatic Drive System Components Ref.No Description Qty Remarks Traction Drive and Brakes Pivot Hydraulic Schematic Seat Components Frame Assembly Frame Front Caster Assembly Yoke Caster Rops TCA16051Page Spindle Assembly Ref. No Description Qty Remarks Deck Lift Assembly Bearing CAP 52 Cutting Deck Mower Deck Cutting Deck GDA10077 Labels Cutting Deck Labels Labels

GBKW2561S, GBKH2752S, GBKW2552S, GBKH2761S specifications

The Great Dane GBKH2761S, GBKW2552S, GBKH2752S, and GBKW2561S are a series of powerful and versatile washing machines designed to meet the needs of modern households. These models stand out for their innovative features, advanced technologies, and user-friendly characteristics, making laundry more efficient and effective.

One of the main features of the Great Dane washing machines is their large capacity, which allows users to wash a significant amount of laundry in one go. This is particularly beneficial for families or individuals with substantial laundry needs, as it reduces the number of loads required and saves valuable time. Additionally, the machines come equipped with a variety of wash programs tailored to different fabric types and soiling levels, ensuring optimal results for every load.

In terms of technologies, these models incorporate intelligent sensors that automatically adjust wash cycles based on the load size and fabric type. This not only enhances cleaning performance but also improves energy efficiency, as the machines consume only the necessary amount of water and electricity. The Great Dane GBKH2761S and GBKW2561S models feature inverter motors that provide quieter operation and greater reliability, translating to longer-lasting performance.

Another standout characteristic of the Great Dane washing machines is their user-friendly interface. The intuitive control panel allows users to select programs and settings easily, while the digital display provides real-time information on the wash cycle. Furthermore, many models are equipped with a delay start feature, offering flexibility for scheduling laundry around busy lifestyles.

In terms of design, the Great Dane series incorporates sleek aesthetics with durable construction, ensuring they not only perform well but also complement modern home interiors. The energy-efficient ratings of these machines make them environmentally friendly choices, helping users reduce their carbon footprint while maintaining high cleaning standards.

Overall, the Great Dane GBKH2761S, GBKW2552S, GBKH2752S, and GBKW2561S represent a blend of cutting-edge technology, capacity, efficiency, and user convenience, making them an ideal choice for consumers seeking reliable and effective washing solutions.
Top Page Image Contents