Great Dane GBKH2761S, GBKW2552S manual Service Mower, Adjusting Park Brake, Alignment Procedure

Page 36

SERVICE MOWER

•To mount in the high position, mount the levers to the top four holes in the mounting bracket.

•To mount in the low position, mount the levers to the bottom four holes in the mounting bracket.

Checking and Aligning Motion Control Levers - Optional Over the Lap Levers

Check Alignment:

1.Park machine safely. (See Parking Safely in the SAFETY section.)

2.Move both motion control levers (A) from the neutral lock to the neutral steer position.

3.Check levers for equal alignment.

•Check gap (B) between the levers. The recommended gap is 3-6 mm (1/8-1/4 in.).

NOTE: If the ends of the levers strike against each other while in the neutral position, move the levers to the neutral lock position and carefully bend them outward. Move them back to the neutral position and check for the recommended gap of 3-6 mm (1/8-1/4 in.).

•If positions of the control levers are unequal, an adjustment is necessary.

Alignment Procedure

1.Adjust position of motion control levers:

•Loosen cap screws (C).

•Slide both levers forward or rearward to desired position on control arm until levers are aligned.

•Tighten cap screws.

Adjusting Park Brake

IMPORTANT: Avoid damage! Due to initial brake wear, the park brake should be checked and adjusted after the first 25 hours of use.

A park brake that is adjusted too tightly could damage the transmission or cause premature brake wear.

1.Park machine safely. (See Parking Safely in the SAFETY section.)

2.Loosen set screw (A).

3.Turn knob (B) clockwise several times.

4.Tighten set screw down in the lower slot. 5.Test park brake.

Service Mower

Removing and Installing Mower Deck Foot Plate

CAUTION: Avoid injury! Always operate the mower with the foot plate installed. Operating with the foot plate removed can cause serious injury.

Service Mower - 34

Page 35 Page 37
Image 36
Page 35 Page 37
Contents OPERATOR’S Manual Page Introduction IntroductionProduct Identification Safety Labels Safety LabelsUnderstanding The Machine Safety Labels Safety Labels Avoid Crushing Safety SafetyUsing a Spark Arrestor Checking Mowing Area Parking SafelyRotating Blades are Dangerous Keep Rops Installed Properly Protect ChildrenAvoid Tipping Use Seat Belt ProperlyMaintenance and Storage Keep Riders OffAvoid High Pressure Fluids Driving Safely on Public RoadsTire Safety Prevent FiresHandling Fuel Safely Daily Operating Checklist OperatingOperating Handling Waste Product and ChemicalsOperator Station Controls Miscellaneous ControlsMounting and Dismounting Machine Safely Raising and Lowering Operator SeatAdjusting Seat Using Seat BeltRaising and Lowering Rops Adjusting Mower Deck Cutting Height Adjusting Mower Deck Anti-Scalp WheelsTesting Safety Systems Testing PTO SwitchTesting Park Brake Switch Testing Neutral Start SwitchTesting Seat Switch Testing the Park BrakeUsing the Park Brake ProcedureUsing the Key Switch Using the PTOUsing the Throttle Lever Using the HourmeterUsing the Choke Using the Motion Control LeversEngage Choke Disengage ChokeForward ReverseGentle Left Turn Gentle Right TurnStarting the Engine Sharp Left TurnSharp Right Turn Engaging Mower Stopping the EngineTransporting Machine Mowing TipsService Intervals Service IntervalsService Lubrication Service LubricationGrease Spray LubricantService Engine Service EngineEngine Warranty Maintenance Statement Avoid FumesChecking Engine Oil Level Changing Engine Oil and FilterOil Capacity With Filter Dry Cleaning Engine Air Intake Screen and Fan Checking and Cleaning Air Filter ElementsAdjusting Carburetor Replacing Fuel FilterService Transmission Service TransmissionHydraulic Oil Checking Hydraulic Oil LevelCleaning Hydraulic Pump Cooling Fins Removing and Installing Traction Drive BeltChecking and Adjusting Motion Control Linkages Neutral Creep Adjustment Maximum Speed Drift AdjustmentCheck Maximum Speed Drift Service Transmission Hydraulic System Hose Routing Service Steering & Brakes Service Steering & BrakesHydraulic System Schematic Removing and Installing Front Caster Wheels Adjusting Front Caster Spindle BearingInstalling Servicing Front Caster Wheel Roller Bearings ChariotHeight Adjustment Procedure Servicing Caster Spindle BearingsCheck Alignment Service Mower Service MowerAdjusting Park Brake Removing and Installing Mower Deck Foot PlateRemoving and Installing Mower Deck Belt Shields Leveling Mower DeckAdjusting Level Side-to-Side Picture Note Discharge chute raised for photo clarityChecking Level Front-to-Rear Checking and Adjusting Cutting Height Adjusting Deck Lift Assist Spring TensionChecking and Adjusting Mower Deck Drive Belt Tension Removing and Installing Mower Deck Drive Belt Checking and Replacing Mower BladesSharpening Blades Balancing BladesReplacing Mower Spindle Bearings Replacing Mower BladesService Electrical Service ElectricalService the Battery Safely Removing and Installing the BatteryCleaning Battery and Terminals Using Booster BatteryReplacing Fuse Burnishing the PTO ClutchWiring Schematic Service Miscellaneous Service MiscellaneousTroubleshooting TroubleshootingCleaning and Repairing Plastic Surfaces Cleaning and Repairing Metal SurfacesEngine Electrical SystemCheck Machine Park BrakeSteering Mower DeckAssembly StorageStorage Assembly Install Motion Control LeversInstall Seat Check Fluid LevelsInstall Rops Specifications SpecificationsGetting Quality Service Getting Quality ServiceEngine and Related Components Kawasaki Ref. No Description Qty Remarks Engine and Related Components Kohler 27 HP Hose OIL Drain Fuel Delivery System Components Over the LAP Control Assembly Electrical and Related Components Fuse Console and Control Assembly Console Hydrostatic Drive System Components Ref.No Description Qty Remarks Traction Drive and Brakes Pivot Hydraulic Schematic Seat Components Frame Assembly Frame Front Caster Assembly Yoke Caster Rops TCA16051Page Spindle Assembly Ref. No Description Qty Remarks Deck Lift Assembly Bearing CAP 52 Cutting Deck Mower Deck Cutting Deck GDA10077 Labels Cutting Deck Labels Labels

GBKW2561S, GBKH2752S, GBKW2552S, GBKH2761S specifications

The Great Dane GBKH2761S, GBKW2552S, GBKH2752S, and GBKW2561S are a series of powerful and versatile washing machines designed to meet the needs of modern households. These models stand out for their innovative features, advanced technologies, and user-friendly characteristics, making laundry more efficient and effective.

One of the main features of the Great Dane washing machines is their large capacity, which allows users to wash a significant amount of laundry in one go. This is particularly beneficial for families or individuals with substantial laundry needs, as it reduces the number of loads required and saves valuable time. Additionally, the machines come equipped with a variety of wash programs tailored to different fabric types and soiling levels, ensuring optimal results for every load.

In terms of technologies, these models incorporate intelligent sensors that automatically adjust wash cycles based on the load size and fabric type. This not only enhances cleaning performance but also improves energy efficiency, as the machines consume only the necessary amount of water and electricity. The Great Dane GBKH2761S and GBKW2561S models feature inverter motors that provide quieter operation and greater reliability, translating to longer-lasting performance.

Another standout characteristic of the Great Dane washing machines is their user-friendly interface. The intuitive control panel allows users to select programs and settings easily, while the digital display provides real-time information on the wash cycle. Furthermore, many models are equipped with a delay start feature, offering flexibility for scheduling laundry around busy lifestyles.

In terms of design, the Great Dane series incorporates sleek aesthetics with durable construction, ensuring they not only perform well but also complement modern home interiors. The energy-efficient ratings of these machines make them environmentally friendly choices, helping users reduce their carbon footprint while maintaining high cleaning standards.

Overall, the Great Dane GBKH2761S, GBKW2552S, GBKH2752S, and GBKW2561S represent a blend of cutting-edge technology, capacity, efficiency, and user convenience, making them an ideal choice for consumers seeking reliable and effective washing solutions.
Top Page Image Contents