Great Dane GBKW2552S, GBKH2761S, GBKH2752S Starting the Engine, Sharp Left Turn, Sharp Right Turn

Page 21

OPERATING

Sharp Left Turn:

•Push right control lever forward and pull left control lever rearward at the same time.

Sharp Right Turn:

4.Push PTO knob (A) down to disengage PTO. 5.Move throttle lever to set engine speed:

•Cold engine: Set throttle lever at the 1/2- to 3/4-throttle position.

•Warm/Hot engine: Set throttle lever to the 1/2-throttle position. 6.Position choke knob (D):

•Cold engine: Pull knob up and hold in choke position.

•Warm/Hot engine: If necessary, pull knob up and hold in choke position.

IMPORTANT: Avoid damage! Starter may be damaged if starter is operated for more than 20 seconds at a time:

• Wait two minutes before trying again if engine does not start.

•Push left control lever forward and pull right control lever rearward at the same time.

Starting the Engine

CAUTION: Avoid injury! Engine exhaust fumes contain carbon monoxide and can cause serious illness or death.

Move the machine to an outside area before running the engine.Do not run an engine in an enclosed area without adequate ventilation.

•Connect a pipe extension to the engine exhaust pipe to direct the exhaust fumes out of the area.

•Allow fresh outside air into the work area to clear the exhaust fumes out.

1.Sit on the operator seat.

2.Lock the park brake.

3.Move both motion control levers to the neutral detent position (standard levers) or neutral lock position (optional “over the lap” levers).

STOP

C

B

7.Turn key switch to start position (B).

If the engine does not start, wait 10 seconds.

•Turn key to start position again for no more than 5 seconds.

•Repeat the procedure if necessary.

IMPORTANT: Avoid damage! Unnecessary engine idling can cause engine overheating, carbon build-up, and poor performance.

8.Release key to run position (C) when engine starts. 9.With engine started:

•Push choke knob to off position.

•Move throttle lever to full-throttle position.

•Unlock the park brake.

Operating - 19

Page 20 Page 22
Image 21
Page 20 Page 22
Contents OPERATOR’S Manual Page Introduction IntroductionProduct Identification Safety Labels Safety LabelsUnderstanding The Machine Safety Labels Safety Labels Avoid Crushing Safety SafetyUsing a Spark Arrestor Checking Mowing Area Parking SafelyRotating Blades are Dangerous Protect Children Keep Rops Installed ProperlyAvoid Tipping Use Seat Belt ProperlyKeep Riders Off Maintenance and StorageAvoid High Pressure Fluids Driving Safely on Public RoadsTire Safety Prevent FiresHandling Fuel Safely Operating Daily Operating ChecklistOperating Handling Waste Product and ChemicalsMiscellaneous Controls Operator Station ControlsMounting and Dismounting Machine Safely Raising and Lowering Operator SeatAdjusting Seat Using Seat BeltRaising and Lowering Rops Adjusting Mower Deck Anti-Scalp Wheels Adjusting Mower Deck Cutting HeightTesting PTO Switch Testing Safety SystemsTesting Park Brake Switch Testing Neutral Start SwitchTesting the Park Brake Testing Seat SwitchUsing the Park Brake ProcedureUsing the PTO Using the Key SwitchUsing the Throttle Lever Using the HourmeterUsing the Motion Control Levers Using the ChokeEngage Choke Disengage ChokeReverse ForwardGentle Left Turn Gentle Right TurnStarting the Engine Sharp Left TurnSharp Right Turn Stopping the Engine Engaging MowerTransporting Machine Mowing TipsService Intervals Service IntervalsService Lubrication Service LubricationGrease Spray LubricantService Engine Service EngineEngine Warranty Maintenance Statement Avoid FumesChecking Engine Oil Level Changing Engine Oil and FilterOil Capacity With Filter Dry Checking and Cleaning Air Filter Elements Cleaning Engine Air Intake Screen and FanAdjusting Carburetor Replacing Fuel FilterService Transmission Service TransmissionHydraulic Oil Checking Hydraulic Oil LevelCleaning Hydraulic Pump Cooling Fins Removing and Installing Traction Drive BeltChecking and Adjusting Motion Control Linkages Neutral Creep Adjustment Maximum Speed Drift AdjustmentCheck Maximum Speed Drift Service Transmission Hydraulic System Hose Routing Service Steering & Brakes Service Steering & BrakesHydraulic System Schematic Adjusting Front Caster Spindle Bearing Removing and Installing Front Caster WheelsInstalling Servicing Front Caster Wheel Roller Bearings ChariotHeight Adjustment Procedure Servicing Caster Spindle BearingsCheck Alignment Service Mower Service MowerAdjusting Park Brake Removing and Installing Mower Deck Foot PlateLeveling Mower Deck Removing and Installing Mower Deck Belt ShieldsAdjusting Level Side-to-Side Picture Note Discharge chute raised for photo clarityChecking Level Front-to-Rear Checking and Adjusting Cutting Height Adjusting Deck Lift Assist Spring TensionChecking and Adjusting Mower Deck Drive Belt Tension Checking and Replacing Mower Blades Removing and Installing Mower Deck Drive BeltBalancing Blades Sharpening BladesReplacing Mower Spindle Bearings Replacing Mower BladesService Electrical Service ElectricalService the Battery Safely Removing and Installing the BatteryUsing Booster Battery Cleaning Battery and TerminalsReplacing Fuse Burnishing the PTO ClutchWiring Schematic Service Miscellaneous Service MiscellaneousTroubleshooting TroubleshootingCleaning and Repairing Plastic Surfaces Cleaning and Repairing Metal SurfacesEngine Electrical SystemCheck Park Brake MachineSteering Mower DeckAssembly StorageStorage Install Motion Control Levers AssemblyInstall Seat Check Fluid LevelsInstall Rops Specifications SpecificationsGetting Quality Service Getting Quality ServiceEngine and Related Components Kawasaki Ref. No Description Qty Remarks Engine and Related Components Kohler 27 HP Hose OIL Drain Fuel Delivery System Components Over the LAP Control Assembly Electrical and Related Components Fuse Console and Control Assembly Console Hydrostatic Drive System Components Ref.No Description Qty Remarks Traction Drive and Brakes Pivot Hydraulic Schematic Seat Components Frame Assembly Frame Front Caster Assembly Yoke Caster TCA16051 RopsPage Spindle Assembly Ref. No Description Qty Remarks Deck Lift Assembly Bearing CAP 52 Cutting Deck Mower Deck Cutting Deck GDA10077 Labels Cutting Deck Labels Labels

GBKW2561S, GBKH2752S, GBKW2552S, GBKH2761S specifications

The Great Dane GBKH2761S, GBKW2552S, GBKH2752S, and GBKW2561S are a series of powerful and versatile washing machines designed to meet the needs of modern households. These models stand out for their innovative features, advanced technologies, and user-friendly characteristics, making laundry more efficient and effective.

One of the main features of the Great Dane washing machines is their large capacity, which allows users to wash a significant amount of laundry in one go. This is particularly beneficial for families or individuals with substantial laundry needs, as it reduces the number of loads required and saves valuable time. Additionally, the machines come equipped with a variety of wash programs tailored to different fabric types and soiling levels, ensuring optimal results for every load.

In terms of technologies, these models incorporate intelligent sensors that automatically adjust wash cycles based on the load size and fabric type. This not only enhances cleaning performance but also improves energy efficiency, as the machines consume only the necessary amount of water and electricity. The Great Dane GBKH2761S and GBKW2561S models feature inverter motors that provide quieter operation and greater reliability, translating to longer-lasting performance.

Another standout characteristic of the Great Dane washing machines is their user-friendly interface. The intuitive control panel allows users to select programs and settings easily, while the digital display provides real-time information on the wash cycle. Furthermore, many models are equipped with a delay start feature, offering flexibility for scheduling laundry around busy lifestyles.

In terms of design, the Great Dane series incorporates sleek aesthetics with durable construction, ensuring they not only perform well but also complement modern home interiors. The energy-efficient ratings of these machines make them environmentally friendly choices, helping users reduce their carbon footprint while maintaining high cleaning standards.

Overall, the Great Dane GBKH2761S, GBKW2552S, GBKH2752S, and GBKW2561S represent a blend of cutting-edge technology, capacity, efficiency, and user convenience, making them an ideal choice for consumers seeking reliable and effective washing solutions.
Top Page Image Contents