Bush Hog HM2007, HM2008, HM2009 manual General Safety Instructions

Page 13

①

②

③

④

⑤

⑥

⑦

Safety

Any operator, repairer and owner must be familiar with the warning instructions for the machine in this manual, before operations commence.

Always work carefully with agricultural machinery. Read through and observe the safety instructions in this manual. Safety is your responsibility.

Pay particular attention to this symbol. It means that there could be a serious hazard. It emphasizes precautions which have to be complied with in order to prevent accidents.

This symbol can be found throughout this manual and on the warning signs on the machine. They are for your safety and should be observed at all times.

General Safety Instructions

Be careful when other people or animals are close by! Never start up the machine when people or animals are close or on the machine or tractor. Never stand between the tractor wheels and the machine.

Adhere to the local laws regarding children’s minimum working age with agricultural machinery.

Use of the machine. The machine must only be used for harvest of common grass and grain crops. The machine must not be used for harvest of maize, lawn mowing in parks and cutting of hedges, neither in vertical or in horizontal position.

Use personal protection devices. Do not wear loose clothing which may catch in any of the moving parts. In dusty conditions a suitable mask must be used.

Take care of excessive sound level. Certain tractor/implement combinations, dependent on operating conditions, may generate a noise level in excess of 85 dB at the operators ear, even in a quiet cab. In these circumstances ear protection must be worn. Keep cab windows and doors CLOSED at all times to reduce noise level.

The machine must only be coupled to a correctly sized tractor, and no other machines or implements must be coupled. The weight of the tractor must correspond to the machine. Observe all local laws. Be careful that the tractor is not unbalanced when coupling.

Make sure that the tractor has the correct PTO. A machine intended for 540 rpm PTO input speed must never be coupled to a tractor with 1000 rpm PTO output speed.

Coupling of tractor and machine must be carried out as explained in the instructions. All lock pins must have locking retainers. Observe all local laws regarding road transport.

Work in a safe way. The tractor engine must ALWAYS be stopped and the ignition key removed before carrying out repairs, cleaning, lubricating or maintaining the machine.

11

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Bush HOG Congratulations HAY Mower Bush HOG Dealer Preparation Check List Safety Signs Signal Words Safety Alert SymbolImportant Safety Precautions Osha Regulations This Act SeeksChild Labor Under 16 Years Old Models HM2007 HM2008 HM2009 Generally about supplementary equipment Model HM2007 Model HM2008 Model HM2009Machine Identification Kg / lb General Safety Instructions SafetyPage Page Model Kg lb HM2007 415 HM2008 440 HM2009 465 Safety instructions during crane lift Page New Machine be careful HM2009 Do the following before coupling the machine to the tractor Preparation For UseModel Color Clip Pin Pawl Remove Clip Pin and Rotate Pawl Fitting of the suspension Mounting couplingMin mm Shortening of the shaft PTO shaftChecking of PTO shaft length Model HM2008 11mm 7/16 Model HM2007 13mm 1/2Model HM2009 8 mm 5/16 Stabilizer Height of the suspensionLifting height If the distance C is too big, raise the lift arm at DPage Transport Transport UnhitchingUnhitching 80 ± 95 ± 60 ft./lbs 70 ft./lbs Operate with safety note the following MaintenanceKnives cutting discs Hole In Front Belt Guard Lubrication generally BeltsOil Filler Plug Oil bevel gearbox Oil cutterbarOil level Plug D Swath Roller Right-hand & Left-hand swath rollers Optional equipmentRight-hand & Left-hand swath boards Hillside Kit As Seen From Below Optional high skid Optional hillside kitFlat Blades Throwing wings Special flat knivesLeft cone 2.8 mm Directions for repair Important, when fitting the gear to the machineHydraulic lifting cylinder Bevel gearboxPage Collar bearings illustration CutterbarFixing of collar bearing ilustration Synchronizing illustrationProblem Possible Cause Correction Problem/Fault Analysis and CorrectionsWinter storage Lubricants Conversion ChartTorque Value Assembly Instructions Support Leg U Bracket 16-40 mmTwisted Strut 12 40 mm Plow Bolt 12 35mm Plow BoltModel HM2009 Model HM2008 Model HM2007 59 ft./lbs Working Direction Gearbox GearboxWorking Direction 10 35 mm 10 30 mm 10 30 mm 30 -10.5 3 mm 10 -30 mm 30 10.5 3 mm Optional Equipment Safety Decals Page Page Bush HOG
Top Page Image Contents