Bush Hog HM2009, HM2008, HM2007 manual 16-40 mm, Support Leg U Bracket

Page 50

Figure 2

Three Point

 

 

Lift Hitch

“U” Bracke

t

 

 

Mainframe assembly unfolded from cutter bar. Three point lift hitch and parking stand have been assem- bled to mainframe. Cutter bar remains in bottom section of steel shipping frame.

 

 

 

 

Cutter Bar

Pivot Pin

 

Mainframe

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Support Leg

 

 

 

 

 

ASSEMBLY

1.Unbolt steel shipping frame. (Figure 1) These frame members will be discarded. Remove plastic wrapping and cut wiring that holds loose pieces together.

2.Arrange loose parts on floor for easy identifi- cation. Lay out fasteners in groups according to size.

3.Unfold mainframe assembly from over cutter bar. Install “T” shaped support leg up through main- frame and pin in place to support the mainframe. Replace nut and bolt in top of support leg. (Figure 2)

4.Remove threaded block from inside of “U” bracket. Slide the three point lift frame over the “U” bracket and assemble together using the threaded

Figure 3 Tighten Bolts “A” Before Bolts “B” B

Three Point

Lift Frame

A

block on the inside and the two square washers on the outside. Fasten with two M16 x 2 - 40 bolts. Use two M16 x 2 - 35 bolts, flatwashers and locknuts through the vetical hloes. (Figure 3)

5.Remove pivot pin from end of mainframe tube. Insure that the threaded plug is screwed in flush with the end of the tube. Fasten the “U” bracket to the mainframe tube using the pin and flatwasher previ- ously removed. Grease the sliding contact points. (Figure 3)

6.Insert and pin the front support leg into posi- tion to further stabilize the mainframe. (Figure 4)

Bolt Block Inside of

Frame With Bolts “A”.

Apply Grease At

Contact Points

Pivot Pin

Plug Should

Be Flush With

End Of Tube

16-40 mm

16-35 mm

“T” Support Leg “U” Bracket

48

Page 49 Page 51
Image 50
Page 49 Page 51
Contents Bush HOG Congratulations HAY Mower Bush HOG Dealer Preparation Check List Safety Alert Symbol Safety Signs Signal WordsImportant Safety Precautions Child Labor Under 16 Years Old This Act SeeksOsha Regulations Models HM2007 HM2008 HM2009 Model HM2007 Model HM2008 Model HM2009 Generally about supplementary equipmentMachine Identification Kg / lb Safety General Safety InstructionsPage Page Model Kg lb HM2007 415 HM2008 440 HM2009 465 Safety instructions during crane lift Page New Machine be careful HM2009 Model Color Preparation For UseDo the following before coupling the machine to the tractor Clip Pin Pawl Remove Clip Pin and Rotate Pawl Mounting coupling Fitting of the suspensionMin mm Checking of PTO shaft length PTO shaftShortening of the shaft Model HM2009 8 mm 5/16 Model HM2007 13mm 1/2Model HM2008 11mm 7/16 Lifting height Height of the suspensionStabilizer If the distance C is too big, raise the lift arm at DPage Unhitching Transport UnhitchingTransport 80 ± 95 ± 60 ft./lbs 70 ft./lbs Knives cutting discs MaintenanceOperate with safety note the following Hole In Front Belt Guard Belts Lubrication generallyOil Filler Plug Oil level Plug D Oil cutterbarOil bevel gearbox Swath Roller Right-hand & Left-hand swath boards Optional equipmentRight-hand & Left-hand swath rollers Hillside Kit As Seen From Below Optional hillside kit Optional high skidFlat Blades Left cone Special flat knivesThrowing wings 2.8 mm Hydraulic lifting cylinder Important, when fitting the gear to the machineDirections for repair Bevel gearboxPage Fixing of collar bearing ilustration CutterbarCollar bearings illustration Synchronizing illustrationProblem/Fault Analysis and Corrections Problem Possible Cause CorrectionWinter storage Torque Value Conversion ChartLubricants Assembly Instructions 16-40 mm Support Leg U Bracket12 40 mm Plow Bolt 12 35mm Plow Bolt Twisted StrutModel HM2009 Model HM2008 Model HM2007 59 ft./lbs Working Direction GearboxWorking Direction Gearbox 10 35 mm 10 30 mm 10 30 mm 30 -10.5 3 mm 10 -30 mm 30 10.5 3 mm Optional Equipment Safety Decals Page Page Bush HOG
Top Page Image Contents