Bush Hog HM2008, HM2007, HM2009 manual 12 40 mm Plow Bolt 12 35mm Plow Bolt, Twisted Strut

Page 51

Figure 4

Front Support Leg

 

 

Apply Grease At Contact Points

7.Fasten curtain frame upright bracket to gear- box using (3) 12 x 30mm bolts, and (1) 12 x 40mm bolt. The 12 x 40mm bolt is located in the bottom rear hole. Leave this bolt loose as it will be used to fasten other components together. (Figure 5)

Figure 5

Pawl

 

 

 

 

12 - 40 mm Plow Bolt 12 - 35mm Plow Bolt

8.At this point the bottom shipping frame should be removed so as not to interfere with installation of the gearbox skid and swathboard. Save the fasten- ers removed from the bottom of the cutter bar as they will be used later at the same location.

9.Install gearbox skid, then gearbox swathboard using the 12 x 40mm bolt that was left loose previ- ously. Use two bolts at front to connect skid and swathboard. (Figure 6) At the rear side of gearbox, use twisted strut to connect skid and swathboard. (Figure 7)

Figure 6 Swathboard

Skid

Figure 7 Skid Swathboard

Twisted Strut

12-40 mm

12 -30 mm (3)

(Also Bottom Front - Not Seen)

10 x 25 mm

12 - 40 mm

49

Image 51
Contents Bush HOG Congratulations HAY Mower Bush HOG Dealer Preparation Check List Safety Signs Signal Words Safety Alert SymbolImportant Safety Precautions This Act Seeks Osha RegulationsChild Labor Under 16 Years Old Models HM2007 HM2008 HM2009 Generally about supplementary equipment Model HM2007 Model HM2008 Model HM2009Machine Identification Kg / lb General Safety Instructions SafetyPage Page Model Kg lb HM2007 415 HM2008 440 HM2009 465 Safety instructions during crane lift Page New Machine be careful HM2009 Preparation For Use Do the following before coupling the machine to the tractorModel Color Clip Pin Pawl Remove Clip Pin and Rotate Pawl Fitting of the suspension Mounting couplingMin mm PTO shaft Shortening of the shaftChecking of PTO shaft length Model HM2007 13mm 1/2 Model HM2008 11mm 7/16Model HM2009 8 mm 5/16 If the distance C is too big, raise the lift arm at D Height of the suspensionStabilizer Lifting heightPage Transport Unhitching TransportUnhitching 80 ± 95 ± 60 ft./lbs 70 ft./lbs Maintenance Operate with safety note the followingKnives cutting discs Hole In Front Belt Guard Lubrication generally BeltsOil Filler Plug Oil cutterbar Oil bevel gearboxOil level Plug D Swath Roller Optional equipment Right-hand & Left-hand swath rollersRight-hand & Left-hand swath boards Hillside Kit As Seen From Below Optional high skid Optional hillside kitFlat Blades Special flat knives Throwing wingsLeft cone 2.8 mm Bevel gearbox Important, when fitting the gear to the machineDirections for repair Hydraulic lifting cylinderPage Synchronizing illustration CutterbarCollar bearings illustration Fixing of collar bearing ilustrationProblem Possible Cause Correction Problem/Fault Analysis and CorrectionsWinter storage Conversion Chart LubricantsTorque Value Assembly Instructions Support Leg U Bracket 16-40 mmTwisted Strut 12 40 mm Plow Bolt 12 35mm Plow BoltModel HM2009 Model HM2008 Model HM2007 59 ft./lbs Gearbox Working Direction GearboxWorking Direction 10 35 mm 10 30 mm 10 30 mm 30 -10.5 3 mm 10 -30 mm 30 10.5 3 mm Optional Equipment Safety Decals Page Page Bush HOG