Bush Hog HM2008, HM2007, HM2009 manual

Page 15

Safety guards. Make sure that ALL GUARDS are in good order and fitted correctly. Do no attempt to start the machine before ensuring this.

Pay particular attention to the plastic guards of the PTO shaft. If damaged they must be replaced. The chain locks of the guards MUST always be fitted on a suitable place on the tractor and the machine to prevent the outer plastic guards turning.

Hydraulics. Be very careful when dealing with hydraulics. Use eye protection and gloves. Escaping hydraulic oil under pressure might penetrate into the skin and cause serious infection. See a doctor if you have been exposed to injury.

Be watchful - damaged hydraulic hoses must be replaced immediately. Never use sealing tape or similar to repair the hoses. The hoses must be securely fixed. All hydraulic hoses of the machine should be replaced at least every 4 years.

Remember when uncoupling, and when leaving tractor/machine. The machine must be in the working position when uncoupling from the tractor. All hydraulic functions must be in neutral posi- tion, the machine must be lowered to the ground and be safely secured. Never allow children to play or be near agricultural machinery.

Drive safely. Be aware of your responsibility - carelessness or slovenliness can cause serious injury or death.

Before transporting on public roads, - always check that the machine is locked with cotter bolt and stop valve, that the coupling is in order, and that possible hydraulic systems and pawls are locked, see the manual of the machine.

Drive carefully. Reduce speed when turning and driving on uneven ground - take care that trac- tor/machine is not swinging and becoming unstable.

Please note that there is danger of overturning when working on slopes and in soft ground condi- tions.

The machine must not be used in situations that unbalances the tractor.

Lighting. It is the responsibility of the owner/operator to provide correct lights and reflectors on the machine, when it is being transported on public roads after dark. Observe the local laws.

Safety equipment. Always carry first aid equipment on the tractor. Also observe local laws con- cerning fire extinguishers. When working with hay or straw a fire extinguisher must be available at all times.

Spare parts. For safety reasons use only original spare parts. If injury occurs when using non- original spare parts the Bush Hog warranty is invalidated.

Maintenance. Take care that the machine is properly maintained and kept in good safe working condition. Never change the technical construction of the machine.

13

Image 15
Contents Bush HOG Congratulations HAY Mower Bush HOG Dealer Preparation Check List Safety Signs Signal Words Safety Alert SymbolImportant Safety Precautions This Act Seeks Osha RegulationsChild Labor Under 16 Years Old Models HM2007 HM2008 HM2009 Generally about supplementary equipment Model HM2007 Model HM2008 Model HM2009Machine Identification Kg / lb General Safety Instructions SafetyPage Page Model Kg lb HM2007 415 HM2008 440 HM2009 465 Safety instructions during crane lift Page New Machine be careful HM2009 Preparation For Use Do the following before coupling the machine to the tractorModel Color Clip Pin Pawl Remove Clip Pin and Rotate Pawl Fitting of the suspension Mounting couplingMin mm PTO shaft Shortening of the shaftChecking of PTO shaft length Model HM2007 13mm 1/2 Model HM2008 11mm 7/16Model HM2009 8 mm 5/16 If the distance C is too big, raise the lift arm at D Height of the suspensionStabilizer Lifting heightPage Transport Unhitching TransportUnhitching 80 ± 95 ± 60 ft./lbs 70 ft./lbs Maintenance Operate with safety note the followingKnives cutting discs Hole In Front Belt Guard Lubrication generally BeltsOil Filler Plug Oil cutterbar Oil bevel gearboxOil level Plug D Swath Roller Optional equipment Right-hand & Left-hand swath rollersRight-hand & Left-hand swath boards Hillside Kit As Seen From Below Optional high skid Optional hillside kitFlat Blades Special flat knives Throwing wingsLeft cone 2.8 mm Bevel gearbox Important, when fitting the gear to the machineDirections for repair Hydraulic lifting cylinderPage Synchronizing illustration CutterbarCollar bearings illustration Fixing of collar bearing ilustrationProblem Possible Cause Correction Problem/Fault Analysis and CorrectionsWinter storage Conversion Chart LubricantsTorque Value Assembly Instructions Support Leg U Bracket 16-40 mmTwisted Strut 12 40 mm Plow Bolt 12 35mm Plow BoltModel HM2009 Model HM2008 Model HM2007 59 ft./lbs Gearbox Working Direction GearboxWorking Direction 10 35 mm 10 30 mm 10 30 mm 30 -10.5 3 mm 10 -30 mm 30 10.5 3 mm Optional Equipment Safety Decals Page Page Bush HOG