Bush Hog HM2009, HM2008, HM2007 manual Winter storage

Page 47

Winter storage

When the season is finished, preparation for winter storage should take place immediately. Start by thoroughly cleaning the machine - then grease the machine thoroughly so that any remaining water is pressed out of the bearings. Change the oil in cutterbar and gearbox and let the machine rotate for a few minutes.

Go over the machine for wear and other defects - make a note of the necessary parts required for the next season and place your order for spare parts.

Observe the safety instructions of the machine. The winter storage operations must only be carried out by competent persons with experience of working with agricultural machinery in a secure and responsible way.

Pre-winter storage procedure:

Check all points mentioned in the MAINTENANCE part shown on page 29. Especially pay attention to the cones of the cutterbar.

Check the cutting discs for wear. The central cutting discs can be interchanged, so that they get the opposite direction of rotation.

Also check the gear wheel of the cutterbar for wear by removing one collar bearing in the left hand side (maximum load). Also check bearing back-lash. Repair of the cutterbar - see page 43.

Check V-belt transmission for wear.

Always make sure that the safety equipment of the machine is not worn or damaged, e.g. the tube protection of the PTO shafts, guards at the rotating parts and the tarpaulin-guard of the machine.

Press the hydraulic piston into the cylinder housing. Dismantle the linkage pins if necessary.

Sprinkle a thin coat of rust preventing oil all over the machine. This is especially important on all parts polished with use. Store the machine in an aerated house.

45

Image 47
Contents Bush HOG Congratulations HAY Mower Bush HOG Dealer Preparation Check List Safety Signs Signal Words Safety Alert SymbolImportant Safety Precautions Child Labor Under 16 Years Old This Act SeeksOsha Regulations Models HM2007 HM2008 HM2009 Generally about supplementary equipment Model HM2007 Model HM2008 Model HM2009Machine Identification Kg / lb General Safety Instructions SafetyPage Page Model Kg lb HM2007 415 HM2008 440 HM2009 465 Safety instructions during crane lift Page New Machine be careful HM2009 Model Color Preparation For UseDo the following before coupling the machine to the tractor Clip Pin Pawl Remove Clip Pin and Rotate Pawl Fitting of the suspension Mounting couplingMin mm Checking of PTO shaft length PTO shaftShortening of the shaft Model HM2009 8 mm 5/16 Model HM2007 13mm 1/2Model HM2008 11mm 7/16 If the distance C is too big, raise the lift arm at D Height of the suspensionStabilizer Lifting heightPage Unhitching Transport UnhitchingTransport 80 ± 95 ± 60 ft./lbs 70 ft./lbs Knives cutting discs MaintenanceOperate with safety note the following Hole In Front Belt Guard Lubrication generally BeltsOil Filler Plug Oil level Plug D Oil cutterbarOil bevel gearbox Swath Roller Right-hand & Left-hand swath boards Optional equipmentRight-hand & Left-hand swath rollers Hillside Kit As Seen From Below Optional high skid Optional hillside kitFlat Blades Left cone Special flat knivesThrowing wings 2.8 mm Bevel gearbox Important, when fitting the gear to the machineDirections for repair Hydraulic lifting cylinderPage Synchronizing illustration CutterbarCollar bearings illustration Fixing of collar bearing ilustrationProblem Possible Cause Correction Problem/Fault Analysis and CorrectionsWinter storage Torque Value Conversion ChartLubricants Assembly Instructions Support Leg U Bracket 16-40 mmTwisted Strut 12 40 mm Plow Bolt 12 35mm Plow BoltModel HM2009 Model HM2008 Model HM2007 59 ft./lbs Working Direction GearboxWorking Direction Gearbox 10 35 mm 10 30 mm 10 30 mm 30 -10.5 3 mm 10 -30 mm 30 10.5 3 mm Optional Equipment Safety Decals Page Page Bush HOG