Bush Hog HM2008, HM2007, HM2009 manual Conversion Chart, Lubricants, Torque Value

Page 48

Conversion Chart

BASIC UNIT:	SI-
	METRIC UNIT:		CONVERSION NUMBER:

LENGTH	1 m	=	39,4 in = 3,3 ft = 1,1 yd = 0,00062 miles (US)

AREA	1 m2	=	1,2 yd2 = 10,8 ft2 = 0,00025 acre = 0,0001 ha

VOLUME	1 dm3 (1 l)	=	61 in = 0,035 ft = 0,22 gallons (lmp) = 0,26 gallons (US) = 1,76 pints

SPEED	1 m/s	=	3,6 km/h = 2,24 mile/h = 3,28 ft/s = 1,94 knob

FORCE	1 N	=	0,10 kp = 0,22 lbf

POWER	1 kW	=	1,36 hk = 1,34 hp = 102 kpm/s = 860 kcal/h = 737 ft lbsf/ s

MASS (Weight)	1 kg	=	2,2 lbs = 0,0197 cwt. = 0,07 slug = 35 oz

MOMENT of Force	1 Nm	=	0,102 kpm = 8,8 lbf in = 0,74 lbf ft

PRESSURE	1 kPa	=	0,01 atm (kp/cm2) = 0,14 lbf/in2 = 7,5 torr

Revolutions	min-1= rpm

Lubricants:

Supplier	Lubricant	Grease Nipples

BP	Energear Hypo 80 W, GL5 Rating	Energrease L 21 M

CASTROL	Castrol EP80 W, GL5 Rating	Castrol MS 3
	Multitrax 75 W/90, GL5 Rating	Castrol Molymax

MOBIL OIL	Mobilube HD 80 W, GL5 Rating	Mobilgrease Special

SHELL	Spirax GX 80 W, GL5 Rating	Retinax MS

TEXACO	Geartex EP-A 80 W, GL5 Rating	Multifak T EP 2
	Multigear S 75W-90, GL5 Rating	Molytex EP 2

*Torque Value:

Torque moment for bolts normal metric thread quality 8.8 black and/or galvanized and ungreased when tightened on a smooth surface or a plain washer.

Thread Diameter mm		5	6	8	10	12	14	16	20	22

Nm	+ 10%	6	10	26	52	90	144	225	436	594
	÷ 0

*Please check Operator’s Manual for special torque settings, i.e., for bolts in knives, bearings, etc., as this table only refers to bolts without a torque setting in the Operator’s Manual.

46

Image 48

Contents Bush HOG Congratulations HAY Mower Bush HOG Dealer Preparation Check List Safety Alert Symbol Safety Signs Signal WordsImportant Safety Precautions This Act Seeks Osha RegulationsChild Labor Under 16 Years Old Models HM2007 HM2008 HM2009 Model HM2007 Model HM2008 Model HM2009 Generally about supplementary equipmentMachine Identification Kg / lb Safety General Safety InstructionsPage Page Model Kg lb HM2007 415 HM2008 440 HM2009 465 Safety instructions during crane lift Page New Machine be careful HM2009 Preparation For Use Do the following before coupling the machine to the tractorModel Color Clip Pin Pawl Remove Clip Pin and Rotate Pawl Mounting coupling Fitting of the suspensionMin mm PTO shaft Shortening of the shaftChecking of PTO shaft length Model HM2007 13mm 1/2 Model HM2008 11mm 7/16Model HM2009 8 mm 5/16 Height of the suspension StabilizerLifting height If the distance C is too big, raise the lift arm at DPage Transport Unhitching TransportUnhitching 80 ± 95 ± 60 ft./lbs 70 ft./lbs Maintenance Operate with safety note the followingKnives cutting discs Hole In Front Belt Guard Belts Lubrication generallyOil Filler Plug Oil cutterbar Oil bevel gearboxOil level Plug D Swath Roller Optional equipment Right-hand & Left-hand swath rollersRight-hand & Left-hand swath boards Hillside Kit As Seen From Below Optional hillside kit Optional high skidFlat Blades Special flat knives Throwing wingsLeft cone 2.8 mm Important, when fitting the gear to the machine Directions for repairHydraulic lifting cylinder Bevel gearboxPage Cutterbar Collar bearings illustrationFixing of collar bearing ilustration Synchronizing illustrationProblem/Fault Analysis and Corrections Problem Possible Cause CorrectionWinter storage Conversion Chart LubricantsTorque Value Assembly Instructions 16-40 mm Support Leg U Bracket12 40 mm Plow Bolt 12 35mm Plow Bolt Twisted StrutModel HM2009 Model HM2008 Model HM2007 59 ft./lbs Gearbox Working Direction GearboxWorking Direction 10 35 mm 10 30 mm 10 30 mm 30 -10.5 3 mm 10 -30 mm 30 10.5 3 mm Optional Equipment Safety Decals Page Page Bush HOG