Bush Hog HM2009, HM2008, HM2007 manual Mounting coupling, Fitting of the suspension

Page 23

①

②

③

Mounting - coupling

The coupling between machine and tractor must be carried out as explained in the instructions. If the machine becomes disconnected from the tractor it could cause severe damage or death.

Fitting of the suspension

Check that the lift arms of the tractor are adjusted to the same height from the ground. Turn the drawbar (A) to the side or remove it. Also check the tire pressure - it is important that the right hand wheel (B) is inflated to the prescribed pressure.

If the width of the tractor is less than 2200 mm (86.6”), measured from the outer edge of the tires, hitch pins (E) must be used. Where the tractor is wider than 2200 mm (86.6”), pins (F) must be used.

NOTE: Model HM2007 is equipped with Cat. II pins to the outside and Cat. I pins to the inside. If used with a Cat. II tractor, a Cat. II bushing must be used on the Cat. I inside pin.

Back the tractor to the machine - fit the lift arms (C) (right hand/left hand) and the top link (D).

Raise the machine with the lift arms (C) so that it is clear of the ground and raise both of the sup- port legs.

Tighten the stabilizer links of the tractor. Check that the arms have the same length on the right hand and left hand sides.

Turn the lock pawl (G) of the stabilizer in the direction indicated by arrow.

NOTE: The lock pawl can only be operated when the machine is coupled to the tractor, and the machine must be raised clear of the ground with the three-point linkage of the tractor.

21

Image 23

Contents Bush HOG Congratulations HAY Mower Bush HOG Dealer Preparation Check List Safety Signs Signal Words Safety Alert SymbolImportant Safety Precautions Child Labor Under 16 Years Old This Act SeeksOsha Regulations Models HM2007 HM2008 HM2009 Generally about supplementary equipment Model HM2007 Model HM2008 Model HM2009Machine Identification Kg / lb General Safety Instructions SafetyPage Page Model Kg lb HM2007 415 HM2008 440 HM2009 465 Safety instructions during crane lift Page New Machine be careful HM2009 Model Color Preparation For UseDo the following before coupling the machine to the tractor Clip Pin Pawl Remove Clip Pin and Rotate Pawl Fitting of the suspension Mounting couplingMin mm Checking of PTO shaft length PTO shaftShortening of the shaft Model HM2009 8 mm 5/16 Model HM2007 13mm 1/2Model HM2008 11mm 7/16 If the distance C is too big, raise the lift arm at D Height of the suspensionStabilizer Lifting heightPage Unhitching Transport UnhitchingTransport 80 ± 95 ± 60 ft./lbs 70 ft./lbs Knives cutting discs MaintenanceOperate with safety note the following Hole In Front Belt Guard Lubrication generally BeltsOil Filler Plug Oil level Plug D Oil cutterbarOil bevel gearbox Swath Roller Right-hand & Left-hand swath boards Optional equipmentRight-hand & Left-hand swath rollers Hillside Kit As Seen From Below Optional high skid Optional hillside kitFlat Blades Left cone Special flat knivesThrowing wings 2.8 mm Bevel gearbox Important, when fitting the gear to the machineDirections for repair Hydraulic lifting cylinderPage Synchronizing illustration CutterbarCollar bearings illustration Fixing of collar bearing ilustrationProblem Possible Cause Correction Problem/Fault Analysis and CorrectionsWinter storage Torque Value Conversion ChartLubricants Assembly Instructions Support Leg U Bracket 16-40 mmTwisted Strut 12 40 mm Plow Bolt 12 35mm Plow BoltModel HM2009 Model HM2008 Model HM2007 59 ft./lbs Working Direction GearboxWorking Direction Gearbox 10 35 mm 10 30 mm 10 30 mm 30 -10.5 3 mm 10 -30 mm 30 10.5 3 mm Optional Equipment Safety Decals Page Page Bush HOG