Bush Hog HM2009, HM2008, HM2007 manual Transport Unhitching

Page 29

①- ②

③

④- ➆

Transport - Unhitching

Transport

As shown the machine can be raised to the vertical position. Raise the machine clear of the ground with the lift arms (A) of the tractor, then raise the machine to the vertical position with the hydraulic cylinder of the machine.

Be careful, check that the curtain frame of the machine can clear the rear wheel of the tractor at (B): If necessary the curtain frame can be turned forward by disengaging the pawl (C).

Be careful. Make sure that no persons are near the machine when it is being raised or lowered during transport. Lock the machine with “L” pin (D) and retaining valve (E). The “L” pin is placed in the hole on the left hand side, when the machine is lowered to working position.

Great care must be taken during transport on public roads. Reduce speed when turn- ing and driving on uneven roads. Observe local laws for road transport.

It is the responsibility of the owner/operator to provide correct lights and reflectors on the machine, when it is transported on public roads after dark.

Unhitching

WARNING

The machine must never be unhitched from the tractor in the transport position. The machine will be unstable and could overturn. Always store the machine in the working position with the cutter bar on the ground.

Raise the machine with the lift arms of the tractor, remove the chain (F) and lower both of the sup- port legs. Engage the lock pawl (G), lower the machine to the ground and unhitch the tractor.

27

Image 29

Contents Bush HOG Congratulations HAY Mower Bush HOG Dealer Preparation Check List Safety Signs Signal Words Safety Alert SymbolImportant Safety Precautions Child Labor Under 16 Years Old This Act SeeksOsha Regulations Models HM2007 HM2008 HM2009 Generally about supplementary equipment Model HM2007 Model HM2008 Model HM2009Machine Identification Kg / lb General Safety Instructions SafetyPage Page Model Kg lb HM2007 415 HM2008 440 HM2009 465 Safety instructions during crane lift Page New Machine be careful HM2009 Model Color Preparation For UseDo the following before coupling the machine to the tractor Clip Pin Pawl Remove Clip Pin and Rotate Pawl Fitting of the suspension Mounting couplingMin mm Checking of PTO shaft length PTO shaftShortening of the shaft Model HM2009 8 mm 5/16 Model HM2007 13mm 1/2Model HM2008 11mm 7/16 Stabilizer Height of the suspensionLifting height If the distance C is too big, raise the lift arm at DPage Unhitching Transport UnhitchingTransport 80 ± 95 ± 60 ft./lbs 70 ft./lbs Knives cutting discs MaintenanceOperate with safety note the following Hole In Front Belt Guard Lubrication generally BeltsOil Filler Plug Oil level Plug D Oil cutterbarOil bevel gearbox Swath Roller Right-hand & Left-hand swath boards Optional equipmentRight-hand & Left-hand swath rollers Hillside Kit As Seen From Below Optional high skid Optional hillside kitFlat Blades Left cone Special flat knivesThrowing wings 2.8 mm Directions for repair Important, when fitting the gear to the machineHydraulic lifting cylinder Bevel gearboxPage Collar bearings illustration CutterbarFixing of collar bearing ilustration Synchronizing illustrationProblem Possible Cause Correction Problem/Fault Analysis and CorrectionsWinter storage Torque Value Conversion ChartLubricants Assembly Instructions Support Leg U Bracket 16-40 mmTwisted Strut 12 40 mm Plow Bolt 12 35mm Plow BoltModel HM2009 Model HM2008 Model HM2007 59 ft./lbs Working Direction GearboxWorking Direction Gearbox 10 35 mm 10 30 mm 10 30 mm 30 -10.5 3 mm 10 -30 mm 30 10.5 3 mm Optional Equipment Safety Decals Page Page Bush HOG