Bush Hog RMB 1865 manual Operating the Tractor and Implement, Foreign Debris Hazards

Page 84

OPERATION

OPERATION

16. OPERATING THE TRACTOR AND IMPLEMENT

THE OPERATOR MUST COMPLETELY UNDERSTAND HOW TO OPERATE THE TRACTOR AND IMPLEMENT AND ALL CONTROLS BEFORE ATTEMPTING TO OPERATE. The operator must read and understand the Safety and Operation Sections of the implement and tractor operator’s manuals. These manuals must be read and explained to any operator who cannot read. Never allow someone to operate the implement and tractor without complete operating instructions.

Before starting any operation, the operator must become familiar with the area to be worked in and any obstacles and hazards contained within to ensure safety to the operator, bystanders, and equipment. Special attention should be paid to foreign debris, rough terrain, steep slopes, and passersby and animals in the area. OPS-U- 0015

16.1 Foreign Debris Hazards

Before mowing, inspect the area to make sure there are no foreign objects that the mower blades could hit or become entangled with. Remove all foreign objects and debris. If objects are too big to remove, mark them clearly and be sure to prevent the mower blades from contacting them.

If you hit a solid object or foreign debris, stop the mower and tractor at once. Immediately idle the engine speed and disengage the PTO. Wait for all mower rotating motion to stop, then raise the mower and move the tractor and implement off the object. Inspect the area and remove, or mark the location of the debris. Inspect the condition of the mower and make any needed repairs immediately. Make sure the blades are not damaged and the carrier is balanced before resuming operation.

Always wear your seat belt securely fastened and only operate the tractor and mower with the ROPS in the raised position. If the tractor or mower hits a tree stump, rock, or bump, a sudden movement could throw you off of the seat and under the tractor and/or mower. The seat belt is your best protection from falling off the tractor and the ROPS provides protection from being crushed during a tractor roll-over. OPS-R-0023A

RMB 1865 11/10

Operation Section 4-30

© 2010 Alamo Group Inc.

Image 84
Contents RMB Warranty Information To the Owner/Operator/DealerOsha Training Requirements Alamo Group Ag. Division is willing to provide Table of Contents Maintenance Section Safety Section Safety General Safety Instructions and PracticesOperator Safety Instructions and Practices SG-36 Wait a minute...Save a life Equipment Operation Safety Instructions and Practices RMB 1865 11/10 Safety Section Stop Mowing if Passersby are Within 300 Feet Unless Safety Safety SGM-06 Maintenance and Service Safety Instructions and Practices RMB 1865 11/10 Safety Section Transporting Safety Instructions and Practices Parts InformationSafety Concluding Safety Instructions and Practices Decal Location Logo NameBooklet ReflectInstruct MULTI-DECALNFS Serial Plate 3688303 Sharp Blades 09.821.35 Decal Description Safety Safety Model Name RMB Safety Safety Safety 3688303 RMB 1865 11/10 Safety Section Federal Laws and Regulations Page Introduction Section Introduction Introduction Before Operating this Machine Assembly Section Assembly Tractor SelectionTractor Preparation Fitting Operator GuardDealer Setup Instructions SWL. Leave in Position AT this StageAttachment to Tractor Assembly Assembly Assembly Assembly Assembly Flailhead Attachment Running UP Procedure OIL RequirementsFitting Control Unit in CAB Removal from Tractor StoragePage Operation Section Operation Standard Equipment and Specifications Standard SpecificationsMachine Specifications Operator Requirements Personal Protective Equipment PPETractor Requirements Rops and Seat BeltOperator Thrown Object Protection Tractor Lighting and SMV Emblem Tractor BallastTractor Safety Devices Tractor Horsepower3-Point Hitch Front End Weight Power Take Off PTOGetting on and OFF the Tractor HydraulicsBoarding the Tractor Dismounting the TractorStarting the Tractor PRE-OPERATION Inspection and Service Tractor Pre-Operation Inspection/ServiceBoom Unit Pre-Operation Inspection and Service Frame Assembly Boom ARM AssemblyHydraulic Line Inspection Hydraulic PUMP/OIL Reservoir Flail Head Inspection Sickle BAR Inspection Do not Operate an Unsafe Tractor or Mower Boom Mower PRE-OPERATION Inspection Machine Controls Cable Controlled Models Only Lever FunctionsOperation Rotor Controls-Gear Hydraulic Machine Only Reversing RotationWith Auto Reset selected BreakawayPowered Slew Wire Trap Rotor Operating SpeedForward Speed Hedge Cutting Procedure High Voltage CablesOperation Driving the Tractor and Implement Brake and Differential Lock Setting Starting the TractorDriving the Tractor and Boom Operating the Tractor and Implement Foreign Debris HazardsBystanders/Passersby Precautions Engaging the Power Take Off PTOOperating Speed and Ground Speed Operating the MowerSGM-08 Operating the Attached Mower Heads FlailSickle Bar Shutting Down the Attached Head TRACTOR, BOOM, and Attached Head Storage OPS-B- 0012HTransporting the Tractor and Implement Transport PositionOperation Transport POSITION-Head Attached Transport POSITION-Head RemovalTransporting on Public Roadways Operation Hauling the Tractor and Implement Operation Troubleshooting Guide Trouble Possible Cause Possible RemedyOperation Operation Maintenance Section Lubrication GeneralFiltration Maintenance Hydraulic SystemHydraulic Hoses Oil SupplyHose Replacement Hose WarrantyFlail Head CablesPTO Gearbox Proper Torque Values for Fasteners Limited Warranty Required of the Owner Required of the OperatorRMB 1865 Rear Mount Boom Mower