Bush Hog RMB 1865 manual Lubrication, General

Page 102

MAINTENANCE

MAINTENANCE

LUBRICATION

General

Grease all locations shown daily.

PTO SHAFT INSPECTION

Regularly check the PTO guards for damage and ensure the antirotation chains are in place and that their anchor points are in good condition. Do not operate the machine with any damaged guards - replace suspect items immediately.

PTO SHAFT LUBRICATION

Lubricate all the points indicated in the diagram below at the intervals stated using a general purpose lithium based grease.

RMB 1866 11/10

Maintenance Section 5-2

© 2010 Alamo Group Inc.

Image 102

Contents RMB Warranty Information To the Owner/Operator/DealerOsha Training Requirements Alamo Group Ag. Division is willing to provide Table of Contents Maintenance Section Safety Section Safety General Safety Instructions and PracticesOperator Safety Instructions and Practices SG-36 Wait a minute...Save a life Equipment Operation Safety Instructions and Practices RMB 1865 11/10 Safety Section Stop Mowing if Passersby are Within 300 Feet Unless Safety Safety SGM-06 Maintenance and Service Safety Instructions and Practices RMB 1865 11/10 Safety Section Transporting Safety Instructions and Practices Parts InformationSafety Concluding Safety Instructions and Practices Decal Location Booklet LogoName ReflectInstruct MULTI-DECALNFS Serial Plate 3688303 Sharp Blades 09.821.35 Decal Description Safety Safety Model Name RMB Safety Safety Safety 3688303 RMB 1865 11/10 Safety Section Federal Laws and Regulations Page Introduction Section Introduction Introduction Before Operating this Machine Assembly Section Assembly Tractor SelectionTractor Preparation Fitting Operator GuardDealer Setup Instructions SWL. Leave in Position AT this StageAttachment to Tractor Assembly Assembly Assembly Assembly Assembly Flailhead Attachment Running UP Procedure OIL RequirementsFitting Control Unit in CAB Removal from Tractor StoragePage Operation Section Operation Standard Equipment and Specifications Standard SpecificationsMachine Specifications Operator Requirements Personal Protective Equipment PPETractor Requirements Rops and Seat BeltOperator Thrown Object Protection Tractor Lighting and SMV Emblem Tractor BallastTractor Safety Devices Tractor Horsepower3-Point Hitch Getting on and OFF the Tractor Front End WeightPower Take Off PTO HydraulicsBoarding the Tractor Dismounting the TractorStarting the Tractor PRE-OPERATION Inspection and Service Tractor Pre-Operation Inspection/ServiceBoom Unit Pre-Operation Inspection and Service Frame Assembly Boom ARM AssemblyHydraulic Line Inspection Hydraulic PUMP/OIL Reservoir Flail Head Inspection Sickle BAR Inspection Do not Operate an Unsafe Tractor or Mower Boom Mower PRE-OPERATION Inspection Machine Controls Cable Controlled Models Only Lever FunctionsOperation Rotor Controls-Gear Hydraulic Machine Only Reversing RotationWith Auto Reset selected BreakawayPowered Slew Wire Trap Rotor Operating SpeedForward Speed Hedge Cutting Procedure High Voltage CablesOperation Driving the Tractor and Implement Brake and Differential Lock Setting Starting the TractorDriving the Tractor and Boom Operating the Tractor and Implement Foreign Debris HazardsBystanders/Passersby Precautions Engaging the Power Take Off PTOOperating Speed and Ground Speed Operating the MowerSGM-08 Operating the Attached Mower Heads FlailSickle Bar Shutting Down the Attached Head TRACTOR, BOOM, and Attached Head Storage OPS-B- 0012HTransporting the Tractor and Implement Transport PositionOperation Transport POSITION-Head Attached Transport POSITION-Head RemovalTransporting on Public Roadways Operation Hauling the Tractor and Implement Operation Troubleshooting Guide Trouble Possible Cause Possible RemedyOperation Operation Maintenance Section Lubrication GeneralHydraulic Hoses Filtration MaintenanceHydraulic System Oil SupplyHose Replacement Hose WarrantyFlail Head CablesPTO Gearbox Proper Torque Values for Fasteners Limited Warranty Required of the Owner Required of the OperatorRMB 1865 Rear Mount Boom Mower