Bush Hog RMB 1865 PRE-OPERATION Inspection and Service, Tractor Pre-Operation Inspection/Service

Page 65
(SG-21)

OPERATION

6. PRE-OPERATION INSPECTION AND SERVICE

Before each use, a pre-operation inspection and service of the implement and tractor must be performed. This includes routine maintenance and scheduled lubrication, inspecting that all safety devices are equipped and functional, and performing needed repairs. DO NOT operate the unit if the pre-operation inspection reveals any condition affecting safe operation. Perform repairs and replacement of damaged and missing parts as soon as noticed. By performing a thorough pre-operation inspection and service, valuable down time and repair cost can be avoided. OPS-U-0029

Periodically inspect all moving parts for wear and replace when necessary with authorized service parts. Look for loose fasteners, worn or broken parts, and leaky or loose fittings. Make sure all pins have cotter pins and washers. Serious injury may occur from not maintaining this machine in good working order.

6.1 Tractor Pre-Operation Inspection/Service

Refer to the tractor operator’s manual to ensure a complete pre-operation inspection and scheduled service is performed according to the manufacturers recommendations. The following are some of the items that require daily service and inspection:

Tire condition/air pressure

Wheel lug bolts

Steering linkage

PTO shield

SMV sign is clean and visible

Tractor’s lights are clean and functional

Tractor Seat belt is in good condition

Tractor ROPS is in good condition

ROPS is in the raised position

No tractor oil leaks

Radiator free of debris

Engine oil level and condition

Engine coolant level and condition

Power brake fluid level

Power steering fluid level

Fuel condition and level

Sufficient lubrication at all lube points

Air filter condition OPS-U-0030

RMB 1865 11/10

Operation Section 4-11

© 2010 Alamo Group Inc.

OPERATION

Image 65
Contents RMB To the Owner/Operator/Dealer Warranty InformationOsha Training Requirements Alamo Group Ag. Division is willing to provide Table of Contents Maintenance Section Safety Section General Safety Instructions and Practices SafetyOperator Safety Instructions and Practices SG-36 Wait a minute...Save a life Equipment Operation Safety Instructions and Practices RMB 1865 11/10 Safety Section Stop Mowing if Passersby are Within 300 Feet Unless Safety Safety SGM-06 Maintenance and Service Safety Instructions and Practices RMB 1865 11/10 Safety Section Parts Information Transporting Safety Instructions and PracticesSafety Concluding Safety Instructions and Practices Decal Location Name LogoBooklet ReflectNFS Serial Plate InstructMULTI-DECAL 3688303 Sharp Blades 09.821.35 Decal Description Safety Safety Model Name RMB Safety Safety Safety 3688303 RMB 1865 11/10 Safety Section Federal Laws and Regulations Page Introduction Section Introduction Introduction Before Operating this Machine Assembly Section Tractor Selection AssemblyFitting Operator Guard Tractor PreparationSWL. Leave in Position AT this Stage Dealer Setup InstructionsAttachment to Tractor Assembly Assembly Assembly Assembly Assembly Flailhead Attachment Fitting Control Unit in CAB Running UP ProcedureOIL Requirements Storage Removal from TractorPage Operation Section Operation Machine Specifications Standard Equipment and SpecificationsStandard Specifications Personal Protective Equipment PPE Operator RequirementsOperator Thrown Object Protection Tractor RequirementsRops and Seat Belt Tractor Ballast Tractor Lighting and SMV Emblem3-Point Hitch Tractor Safety DevicesTractor Horsepower Power Take Off PTO Front End WeightGetting on and OFF the Tractor HydraulicsDismounting the Tractor Boarding the TractorStarting the Tractor Tractor Pre-Operation Inspection/Service PRE-OPERATION Inspection and ServiceBoom Unit Pre-Operation Inspection and Service Hydraulic Line Inspection Frame AssemblyBoom ARM Assembly Hydraulic PUMP/OIL Reservoir Flail Head Inspection Sickle BAR Inspection Do not Operate an Unsafe Tractor or Mower Boom Mower PRE-OPERATION Inspection Cable Controlled Models Only Lever Functions Machine ControlsOperation Reversing Rotation Rotor Controls-Gear Hydraulic Machine OnlyBreakaway With Auto Reset selectedPowered Slew Forward Speed Wire TrapRotor Operating Speed High Voltage Cables Hedge Cutting ProcedureOperation Driving the Tractor and Implement Starting the Tractor Brake and Differential Lock SettingDriving the Tractor and Boom Foreign Debris Hazards Operating the Tractor and ImplementEngaging the Power Take Off PTO Bystanders/Passersby PrecautionsOperating the Mower Operating Speed and Ground SpeedSGM-08 Sickle Bar Operating the Attached Mower HeadsFlail Shutting Down the Attached Head OPS-B- 0012H TRACTOR, BOOM, and Attached Head StorageTransport Position Transporting the Tractor and ImplementOperation Transport POSITION-Head Removal Transport POSITION-Head AttachedTransporting on Public Roadways Operation Hauling the Tractor and Implement Operation Trouble Possible Cause Possible Remedy Troubleshooting GuideOperation Operation Maintenance Section General LubricationHydraulic System Filtration MaintenanceHydraulic Hoses Oil SupplyHose Warranty Hose ReplacementCables Flail HeadPTO Gearbox Proper Torque Values for Fasteners Limited Warranty Required of the Operator Required of the OwnerRMB 1865 Rear Mount Boom Mower