Bush Hog RMB 1865 manual Assembly

Page 49

ASSEMBLY

Raise the stand legs into the work position and secure with lock pins.

Tighten check chains and/or stabilizer bars.

Fit machine controls into the cab. (Optional Cables available)

Measure PTO and cut to dimension shown.

Note: For subsequent use on different tractors measure again - there must be a minimum shaft overlap of 150mm.

RMB 1865 11/10

Assembly Section 3-9

© 2010 Alamo Group Inc.

ASSEMBLY

Image 49
Contents RMB To the Owner/Operator/Dealer Warranty InformationOsha Training Requirements Alamo Group Ag. Division is willing to provide Table of Contents Maintenance Section Safety Section General Safety Instructions and Practices SafetyOperator Safety Instructions and Practices SG-36 Wait a minute...Save a life Equipment Operation Safety Instructions and Practices RMB 1865 11/10 Safety Section Stop Mowing if Passersby are Within 300 Feet Unless Safety Safety SGM-06 Maintenance and Service Safety Instructions and Practices RMB 1865 11/10 Safety Section Parts Information Transporting Safety Instructions and PracticesSafety Concluding Safety Instructions and Practices Decal Location Name LogoBooklet ReflectMULTI-DECAL InstructNFS Serial Plate 3688303 Sharp Blades 09.821.35 Decal Description Safety Safety Model Name RMB Safety Safety Safety 3688303 RMB 1865 11/10 Safety Section Federal Laws and Regulations Page Introduction Section Introduction Introduction Before Operating this Machine Assembly Section Tractor Selection AssemblyFitting Operator Guard Tractor PreparationSWL. Leave in Position AT this Stage Dealer Setup InstructionsAttachment to Tractor Assembly Assembly Assembly Assembly Assembly Flailhead Attachment OIL Requirements Running UP ProcedureFitting Control Unit in CAB Storage Removal from TractorPage Operation Section Operation Standard Specifications Standard Equipment and SpecificationsMachine Specifications Personal Protective Equipment PPE Operator RequirementsRops and Seat Belt Tractor RequirementsOperator Thrown Object Protection Tractor Ballast Tractor Lighting and SMV EmblemTractor Horsepower Tractor Safety Devices3-Point Hitch Power Take Off PTO Front End WeightGetting on and OFF the Tractor HydraulicsDismounting the Tractor Boarding the TractorStarting the Tractor Tractor Pre-Operation Inspection/Service PRE-OPERATION Inspection and ServiceBoom Unit Pre-Operation Inspection and Service Boom ARM Assembly Frame AssemblyHydraulic Line Inspection Hydraulic PUMP/OIL Reservoir Flail Head Inspection Sickle BAR Inspection Do not Operate an Unsafe Tractor or Mower Boom Mower PRE-OPERATION Inspection Cable Controlled Models Only Lever Functions Machine ControlsOperation Reversing Rotation Rotor Controls-Gear Hydraulic Machine OnlyBreakaway With Auto Reset selectedPowered Slew Rotor Operating Speed Wire TrapForward Speed High Voltage Cables Hedge Cutting ProcedureOperation Driving the Tractor and Implement Starting the Tractor Brake and Differential Lock SettingDriving the Tractor and Boom Foreign Debris Hazards Operating the Tractor and ImplementEngaging the Power Take Off PTO Bystanders/Passersby PrecautionsOperating the Mower Operating Speed and Ground SpeedSGM-08 Flail Operating the Attached Mower HeadsSickle Bar Shutting Down the Attached Head OPS-B- 0012H TRACTOR, BOOM, and Attached Head StorageTransport Position Transporting the Tractor and ImplementOperation Transport POSITION-Head Removal Transport POSITION-Head AttachedTransporting on Public Roadways Operation Hauling the Tractor and Implement Operation Trouble Possible Cause Possible Remedy Troubleshooting GuideOperation Operation Maintenance Section General LubricationHydraulic System Filtration MaintenanceHydraulic Hoses Oil SupplyHose Warranty Hose ReplacementCables Flail HeadPTO Gearbox Proper Torque Values for Fasteners Limited Warranty Required of the Operator Required of the OwnerRMB 1865 Rear Mount Boom Mower