Bush Hog RMB 1865 Tractor Requirements, Rops and Seat Belt, Operator Thrown Object Protection

Page 59

OPERATION

3. TRACTOR REQUIREMENTS

In addition to tractor horsepower and size required to operate the mower unit, the tractor must also be properly equipped to provide operator protection, to alert approaching vehicle drivers of the tractor’s presence, and to ensure tractor stability when mowing with the boom fully extended.

Tractor Requirements and Capabilities

SAE/ISO ROPS cab and seat belt

Operator Protection .......................... Tractor must be equipped with protective structure such as operator cage or lexan window to protect operator from thrown object and falling objects

Tractor Safety Devices .................... Slow Moving Vehicle (SMV) emblem, lighting,

Tractor Ballast ................................. As required to maintain at least 1500 lbs. on left rear tire

3.1ROPS and Seat Belt

The tractor must be equipped with a Roll-Over-Protective-Structure (ROPS) (tractor cab or roll-bar) and seat belt to protect the operator from falling off the tractor, especially during a roll over where the driver could be crushed and killed. Only operate the tractor with the ROPS in the raised position and seat belt fastened. Tractor models not equipped with a ROPS and seat belt should have these life saving features installed by an authorized dealer. OPS-U- 0003

Operate this Equipment only with a Cab Tractor. Always wear seat belts. (SG-45)

3.2 Operator Thrown Object Protection

The tractor must be equipped with protective equipment to shield the operator from falling and thrown objects. For cab tractors, the tractor must be equipped with an operator safety screen on its right side or the right side windows must be fitted with a shatter proof safety window.

OPS-B- 0001_B

Never operate the Tractor and Mower Unit without an OPS (Operators Protective Structure) or Cab to prevent injury from objects thrown from ground or from overhead trimming. Stop mowing if workers or passersby are within 300 feet. (SBM-9)

RMB 1865 11/10

Operation Section 4-5

© 2010 Alamo Group Inc.

OPERATION

Image 59
Contents RMB To the Owner/Operator/Dealer Warranty InformationOsha Training Requirements Alamo Group Ag. Division is willing to provide Table of Contents Maintenance Section Safety Section General Safety Instructions and Practices SafetyOperator Safety Instructions and Practices SG-36 Wait a minute...Save a life Equipment Operation Safety Instructions and Practices RMB 1865 11/10 Safety Section Stop Mowing if Passersby are Within 300 Feet Unless Safety Safety SGM-06 Maintenance and Service Safety Instructions and Practices RMB 1865 11/10 Safety Section Parts Information Transporting Safety Instructions and PracticesSafety Concluding Safety Instructions and Practices Decal Location Reflect LogoName BookletNFS Serial Plate InstructMULTI-DECAL 3688303 Sharp Blades 09.821.35 Decal Description Safety Safety Model Name RMB Safety Safety Safety 3688303 RMB 1865 11/10 Safety Section Federal Laws and Regulations Page Introduction Section Introduction Introduction Before Operating this Machine Assembly Section Tractor Selection AssemblyFitting Operator Guard Tractor PreparationSWL. Leave in Position AT this Stage Dealer Setup InstructionsAttachment to Tractor Assembly Assembly Assembly Assembly Assembly Flailhead Attachment Fitting Control Unit in CAB Running UP ProcedureOIL Requirements Storage Removal from TractorPage Operation Section Operation Machine Specifications Standard Equipment and SpecificationsStandard Specifications Personal Protective Equipment PPE Operator RequirementsOperator Thrown Object Protection Tractor RequirementsRops and Seat Belt Tractor Ballast Tractor Lighting and SMV Emblem3-Point Hitch Tractor Safety DevicesTractor Horsepower Hydraulics Front End WeightPower Take Off PTO Getting on and OFF the TractorDismounting the Tractor Boarding the TractorStarting the Tractor Tractor Pre-Operation Inspection/Service PRE-OPERATION Inspection and ServiceBoom Unit Pre-Operation Inspection and Service Hydraulic Line Inspection Frame AssemblyBoom ARM Assembly Hydraulic PUMP/OIL Reservoir Flail Head Inspection Sickle BAR Inspection Do not Operate an Unsafe Tractor or Mower Boom Mower PRE-OPERATION Inspection Cable Controlled Models Only Lever Functions Machine ControlsOperation Reversing Rotation Rotor Controls-Gear Hydraulic Machine OnlyBreakaway With Auto Reset selectedPowered Slew Forward Speed Wire TrapRotor Operating Speed High Voltage Cables Hedge Cutting ProcedureOperation Driving the Tractor and Implement Starting the Tractor Brake and Differential Lock SettingDriving the Tractor and Boom Foreign Debris Hazards Operating the Tractor and ImplementEngaging the Power Take Off PTO Bystanders/Passersby PrecautionsOperating the Mower Operating Speed and Ground SpeedSGM-08 Sickle Bar Operating the Attached Mower HeadsFlail Shutting Down the Attached Head OPS-B- 0012H TRACTOR, BOOM, and Attached Head StorageTransport Position Transporting the Tractor and ImplementOperation Transport POSITION-Head Removal Transport POSITION-Head AttachedTransporting on Public Roadways Operation Hauling the Tractor and Implement Operation Trouble Possible Cause Possible Remedy Troubleshooting GuideOperation Operation Maintenance Section General LubricationOil Supply Filtration MaintenanceHydraulic System Hydraulic HosesHose Warranty Hose ReplacementCables Flail HeadPTO Gearbox Proper Torque Values for Fasteners Limited Warranty Required of the Operator Required of the OwnerRMB 1865 Rear Mount Boom Mower