Meridian Audio FDP-DILA2 warranty Quick Reference Guide for PC Menu Mode, Menu Operations

Menu Operations

■Quick Reference Guide for PC Menu Mode

Main Menu in PC Menu Mode (While receiving computer-related signals)

Image adj. → (Refer to page 49)

	Contrast:			Contrast of the picture image being projected can be adjusted. (–30 to +30, 0*)
	Brightness:			Brightness of the picture image being projected can be adjusted. (–30 to +30, 0*)
	Sharpness:			Adjust the outline of letters etc. (1 / 2 / 3 / 4 / 5, 3*)
	All reset:			Resets above items to the factory set values.
Set up			Yes / No
	Tracking:			The lateral size and display area of picture image can be adjusted. (–128 to +127)
				→ (Refer to page 47)
	Phase:			Flickering or dim picture image can be adjusted. (0 to 31) → (Refer to page 47)
	Position:			Video screen position and menu position can be adjusted. → (Refer to page 51)
			Disp. Posi. / Menu
	Resize:			The relationship between the number of pixels (resolution) and the screen can be
				selected. → (Refer to page 53)
			“1:1”:		Picture image is projected with its original size.
			Panel:		Picture image is enlarged to the full size.
			Aspect*:		Picture image is enlarged while maintaining the original aspect ratio.
	Clamp:			Selectable clamp position. Normally, set to “BP”. ST / BP*
Color temp.
	Color temp.:			Adjustable color temperature, Low/Middle* /High.
				Will be adjusted to correct reddish or blueish image.
	RED:			Adjusts the red level. (o to 255, the adjustable range varies depending on signals)
	GREEN:			Adjusts the green level. (o to 255, the adjustable range varies depending on signals)
	BLUE:			Adjusts the blue level. (o to 255, the adjustable range varies depending on signals)
	All-reset:			Reset above items to the factory set values.
			Yes/No
Options → (Refer to page 54)
Options 1
	Menu display:			15sec* (Menu disappears in 15 seconds.) / ON (Menu stays on.)
	Line display:			5sec* (Line display such as “PC1” or “PC2” appears on top right of the screen for 5
				seconds when the VIDEO or PC button is pressed.) / OFF (Line display does not
				appear.)
	Lamp time display:
		ON*:		Displays when the lamp use time reaches 1000 hours when set in the LPC or LOC mode.
		OFF:		Does not display when the lamp use time reaches 1000 hours when set in the LPC or LOC
				mode.
	Keystone:			Press ENTER to enter the Keystone submenu.
		Keystone:			Adjust to correct the trapezoidal distortion of the projected image.
					(–80 to +128, 0*)
	Lamp control:
		Normal*:		Used as a normal lamp.
		LPC:		Lamp brightness is aLutomatically controlled with time.
		LOC:		Lamp brightness is controlled in 7 levels (-6 to 0) irrespective of the time. This is set within
				the menu.
	Page 2:			Press ENTER to enter the “Page 2” submenu.
			Flip H:		OFF* / ON (Select for upside-down hanging on the ceiling.)
			Flip V:		OFF* / ON (Select for upside-down hanging on the ceiling.)
			RS-232C [bps]:		Selectable baud rate (transmission speed). 9600 / 19200*
			Sleep time [min]:		Selectable sleep times. If no-signal condition continues for the
					period of selected time (Unite: Minutes), the projector enters the
					stand-by mode. 15 / 30 / 60 / OFF*
			Page 1:		Press ENTER to return to the “Page 1” submenu.
Language				Language for on-screen display. → (Refer to page 46)
	Japanese / English* / German / Spanish / Italian / French
Information → (Refer to page 56)
	Input:			Shows the terminal name selected by the PC button. (PC1 or PC2)
	Switcher:			This display currently has no meaning. (“CH.0” is usually displayed to indicate that it is not being used.)
	Resolution:			Shows the resolution of the input signal being received. (Horizontal ⋅ Vertical)
				It may not be displayed correctly with some input signals.
	Frequency H:			Shows the horizontal frequency of the input signal being received. ( kHz)
	Frequency V:			Shows the vertical frequency of the input signal being received. ( Hz)
	Lamp time:			Accumulated used hours of the light-source lamp.

* : Factory set value.

41