Meridian Audio FDP-DILA2 warranty Replacing the Fuse, the projector and the wall outlet

Page 56

Replacing the Fuse

Replacing the Fuse

A fuse is used to protect the power source of the projector. If the fuse is blown, replace it. When the power switch is turned on but no power is supplied to the projector, check the fuse. If there are any unclear points, contact the dealer where you purchased your projector, or consult the Service center.

CAUTION

•When replacing the fuse, use the same rating and type (12 A 250 V). Otherwise, a fire may occur and/or the projector may be damaged.

1Turn off the main power switch and disconnect the power cord from both

the projector and the wall outlet.

In stand-by state (the STAND BY indicator lights on), place the MAIN POWER switch of OFF [] position.

2Loosen the fuse holder to remove it.

To loosen the fuse holder, use a Phillips screwdriver.

3Remove the fuse from the fuse holder you just removed.

4Install the new fuse (not supplied) into the fuse holder.

5Reinstall the fuse holder into the

projector.

To reinstall the fuse holder, use a Phillips screwdriver.

Fuse holder

Phillips screwdriver

Fuse (12 A, 250 V)

Fuse holder

Fuse (12 A, 250 V)

Fuse holder

56

Image 56

Contents FDP-DILA2 Installation and Operations ManualHome Theater Optimized SAFETY PRECAUTIONS IMPORTANT INFORMATION IMPORTANT SAFEGUARDSAbout the installation place About burning-inof the D-ILAdevicePower cord Contents for Macintosh Accessoriesfor checking operation Controls and Features 3AC IN power input terminal5MAIN POWER switch 1Exhaust ventsControls and Features pConnector panelwAir inlet eControl panelControls and Features t y utAir inlet filter yOpening for replacing the light-sourcelampControl Panel on the Projector Controls and Features pPRESET buttoneLAMP indicator rTEMP indicatorControls and Features 1PC computer 1 input terminal D-sub 3-row15 pin3DVI terminal DVI-D24 pin 4 PC computer 2 input terminals BNC ⋅Remote Control Unit Controls and Features rDIGITAL ZOOM T/W buttonstPC buttons ySCREEN W/S buttonsInstall the batteries Precautions for using batteriesControls and Features Open the back coverCAUTIONS Installing the ProjectorPrecautions for Installation Adjusting the Inclination of the Projector Adjusting the vertical angle of the projectorInstalling the Projector Leveling the projectorInstalling the Projector against the Screen Installing the ProjectorSide view Top viewOptional Lenses Installing the ProjectorProjection Distance and Screen Size Installing the Projector 2Loosen the SHIFT LOCK fixing boltscreen 4Tighten the SHIFT LOCK fixing bolt firmlyUsing as a wireless remote control unit Installing the ProjectorCAUTIONS When installing adjusting/setting the unitInstalling the Projector Connecting to Various Devices Video signalsComputer signals Note: Instructions for installing the VideoAllowable input signals Connecting to Various DevicesMemo Connecting to Video DevicesConnecting to Various Devices Memo Connecting to HDTV Devices/DVD PlayersConnecting to Various Devices Connecting to Devices which Control the Projector Connecting to Various DevicesConnection to an IBM PC or IBM-compatiblecomputer Connecting to Computer DevicesConnecting to Various Devices Connecting to Various Devices 1Release the stopper at each end andopen the ferrite core 2 Wind the cord around the ferrite coreConnecting the Power Cord Basic Operations Lamp control settings1. Turning on the Power 1 Turn on the MAIN POWER switchRemote control unit Turning off the PowerRemote control unit Remote control unitRemote control unit Projector’s buttons3. Adjust the Screen Size Zooming Remote control unit4. Adjust Focus 5. Setting the Screen Aspect RatioRemote control unit Projector’s buttonsTurning off Image HIDE Removing the Trapezoidal Distortion of the ImageBasic Operations Remote control unitQuick Alignment Function QUICK ALIGN Remote control unit Displaying a Still Picture FREEZEZooming a Part of the Image DIGITAL ZOOM T/W Basic OperationsQuick Reference Guide for No signal Menu Mode Menu OperationsMenu Transition Diagram in No signal Menu Mode Menu Transition Diagram in Video Menu Mode Menu OperationsFactory set value Quick Reference Guide for Video Menu ModeMenu Operations Menu Transition Diagram in PC Menu Mode Menu OperationsQuick Reference Guide for PC Menu Mode Menu Operationsor adjust the value 4Press the cursor button 5 or ∞ toselect an item in the submenu 1Press the MENU buttonRemote control unit ProjectorVideo menu mode PC menu modeChanging the Color System Video Menu Mode Only 1Press the MENU buttonChanging the Language Display 1Press the MENU button3Set the language with the cursor button 5 or ∞ 1Press the MENU buttonAdjusting Tracking/Phase Adjust the tracking or phase with the cursor 2 or1Press the MENU button Menu Operations1Press the MENU button Make adjustment with the cursor 2 or To perform All ResetHowever, some fine-tuningfor specific installations may be requiredAdjusting Color temperature To perform All Reset1Press the MENU button buttonmenu Adjusting the Video Screen/Menu Position1Press the MENU button 1Press the MENU button 1Press the MENU button Setting and Adjusting Other Functions OPTIONS Make adjustment with the cursor 2 or1Press the MENU button Menu OperationsMenu Operations Getting Information 1Press the MENU button3Press the MENU button to exit the menu mode Menu OperationsReplacing the Fuse 5Reinstall the fuse holder into the projectorthe projector and the wall outlet 2Loosen the fuse holder to remove itReplacing the Light-SourceLamp Light-sourcelamp and lamp use timeReplacing the Light-SourceLamp CAUTIONSLoosen the two screws with a flat-endscrewdriver 4Replace the lamp-replacementopening 5Reset the lamp use time3 Insert the new light-sourcelamp fully inside and fasten the screwsResetting the Lamp Use Time 1Turn on the MAIN POWER switch to goProjector’s button into stand-bymodeCleaning and Replacing the Filter Cover 1Turn off the MAIN POWER switch3Clean the filter 4Reinstall the filterTroubleshooting Maintenance TroubleshootingWarning Indication Action to be taken for warning indicationWarning Messages MessageCause Corrective actionWarning Messages Memo Displayed when the lamp controlWarning Messages Specifications Optical mechanism systemElectrical system Input terminalsSpecifications GeneralSpecifications FrontSide 22.430Specifications Y/C terminalRS-232Cterminal PC1 terminal/PC OUT terminal2. Command Format RS-232Cexternal control1. Communication Specifications 3. Control command table 2-3Parameters used for the data formatRS-232Cexternal control 1 Numeric valueFor lens unit GL-M2915SG1.5 AppendixFor lens unit GL-M2910G1 For lens unit GL-M2930SZG2.9 to AppendixFor lens unit GL-M2920ZG2 to Page Page Page WARRANTY LIMITED WARRANTYFaroudja Laboratories A Division of Genesis Microchip Corp