Meridian Audio FDP-DILA2 warranty Installing the Projector, Precautions for Installation, Cautions

Page 15
Installing the Projector

Installing the Projector

Precautions for Installation

CAUTIONS

1.Before installation, do not connect the projector’s power cord.

2.Do not install the projector in the following places:

Where there is water, humidity or dust.

Where the projector may be subjected to oil, smoke or cigarette smoke.

On a soft surface such as a carpet or cushion.

Where the projector may be subjected to direct sunlight.

Where temperature is high or humidity is low.

Allowable operation temperature range: 41°F to 95°F (+5°C to +35°C)

Allowable relative humidity range: 20% to 80% (no condensation)

Allowable storage temperature range: 14°F to 140°F (–10°C to +60°C)

When installing the projector, observe the following:

Do not use the projector placed on its side.

Avoid using the projector placed on its side. This could cause a malfunction.

Use the projector within the specified angle.

Do not use the projector inclined ±30° horizontally (left/right). This could cause color variation or shorten the lamp life.

Do not block the exhaust vents.

Do not use a cover which encloses the projector air-tight or blocks the exhaust vents. Allow sufficient space around the projector. When the projector is enclosed in a space of the following dimensions, use an air conditioner so the temperature inside becomes equal to the outside temperature.

Allowable minimum space required

300mm

200mm

600mm

300mm

200mm

15

Image 15
Contents Installation and Operations Manual Home Theater OptimizedFDP-DILA2 About burning-inof the D-ILAdevice SAFETY PRECAUTIONSIMPORTANT INFORMATION IMPORTANT SAFEGUARDS About the installation placePower cord Contents Accessories for checking operationfor Macintosh 1Exhaust vents Controls and Features3AC IN power input terminal 5MAIN POWER switcheControl panel Controls and FeaturespConnector panel wAir inletyOpening for replacing the light-sourcelamp Controls and Featurest y u tAir inlet filterControl Panel on the Projector rTEMP indicator Controls and FeaturespPRESET button eLAMP indicator4 PC computer 2 input terminals BNC ⋅ Controls and Features1PC computer 1 input terminal D-sub 3-row15 pin 3DVI terminal DVI-D24 pinRemote Control Unit ySCREEN W/S buttons Controls and FeaturesrDIGITAL ZOOM T/W buttons tPC buttonsOpen the back cover Install the batteriesPrecautions for using batteries Controls and FeaturesInstalling the Projector Precautions for InstallationCAUTIONS Leveling the projector Adjusting the Inclination of the ProjectorAdjusting the vertical angle of the projector Installing the ProjectorTop view Installing the Projector against the ScreenInstalling the Projector Side viewInstalling the Projector Projection Distance and Screen SizeOptional Lenses 4Tighten the SHIFT LOCK fixing bolt firmly Installing the Projector2Loosen the SHIFT LOCK fixing bolt screenInstalling the Projector Using as a wireless remote control unitWhen installing adjusting/setting the unit Installing the ProjectorCAUTIONS Note: Instructions for installing the Video Connecting to Various DevicesVideo signals Computer signalsConnecting to Various Devices Allowable input signalsConnecting to Video Devices Connecting to Various DevicesMemo Connecting to HDTV Devices/DVD Players Connecting to Various DevicesMemo Connecting to Various Devices Connecting to Devices which Control the ProjectorConnecting to Computer Devices Connecting to Various DevicesConnection to an IBM PC or IBM-compatiblecomputer 2 Wind the cord around the ferrite core Connecting to Various Devices1Release the stopper at each end and open the ferrite coreConnecting the Power Cord Lamp control settings Basic OperationsTurning off the Power 1. Turning on the Power1 Turn on the MAIN POWER switch Remote control unitProjector’s buttons Remote control unitRemote control unit Remote control unit5. Setting the Screen Aspect Ratio 3. Adjust the Screen Size ZoomingRemote control unit 4. Adjust FocusRemoving the Trapezoidal Distortion of the Image Remote control unitProjector’s buttons Turning off Image HIDERemote control unit Quick Alignment Function QUICK ALIGNBasic Operations Basic Operations Remote control unitDisplaying a Still Picture FREEZE Zooming a Part of the Image DIGITAL ZOOM T/WMenu Operations Menu Transition Diagram in No signal Menu ModeQuick Reference Guide for No signal Menu Mode Menu Operations Menu Transition Diagram in Video Menu ModeQuick Reference Guide for Video Menu Mode Menu OperationsFactory set value Menu Operations Menu Transition Diagram in PC Menu ModeMenu Operations Quick Reference Guide for PC Menu Mode1Press the MENU button or adjust the value4Press the cursor button 5 or ∞ to select an item in the submenuPC menu mode Remote control unitProjector Video menu mode1Press the MENU button Changing the Color System Video Menu Mode Only1Press the MENU button Changing the Language Display1Press the MENU button 3Set the language with the cursor button 5 or ∞Menu Operations Adjusting Tracking/PhaseAdjust the tracking or phase with the cursor 2 or 1Press the MENU button1Press the MENU button installations may be required Make adjustment with the cursor 2 orTo perform All Reset However, some fine-tuningfor specificbutton Adjusting Color temperatureTo perform All Reset 1Press the MENU buttonAdjusting the Video Screen/Menu Position 1Press the MENU buttonmenu 1Press the MENU button 1Press the MENU button Menu Operations Setting and Adjusting Other Functions OPTIONSMake adjustment with the cursor 2 or 1Press the MENU buttonMenu Operations Menu Operations Getting Information1Press the MENU button 3Press the MENU button to exit the menu mode2Loosen the fuse holder to remove it Replacing the Fuse5Reinstall the fuse holder into the projector the projector and the wall outletLight-sourcelamp and lamp use time Replacing the Light-SourceLampCAUTIONS Replacing the Light-SourceLampLoosen the two screws with a flat-endscrewdriver inside and fasten the screws 4Replace the lamp-replacementopening5Reset the lamp use time 3 Insert the new light-sourcelamp fullyinto stand-bymode Resetting the Lamp Use Time1Turn on the MAIN POWER switch to go Projector’s button4Reinstall the filter Cleaning and Replacing the Filter Cover1Turn off the MAIN POWER switch 3Clean the filterTroubleshooting Troubleshooting MaintenanceAction to be taken for warning indication Warning IndicationCorrective action Warning MessagesMessage CauseWarning Messages Displayed when the lamp control Warning MessagesMemo Input terminals SpecificationsOptical mechanism system Electrical systemGeneral Specifications22.430 SpecificationsFront SidePC1 terminal/PC OUT terminal SpecificationsY/C terminal RS-232CterminalRS-232Cexternal control 1. Communication Specifications2. Command Format 1 Numeric value 3. Control command table2-3Parameters used for the data format RS-232Cexternal controlAppendix For lens unit GL-M2910G1For lens unit GL-M2915SG1.5 Appendix For lens unit GL-M2920ZG2 toFor lens unit GL-M2930SZG2.9 to Page Page Page A Division of Genesis Microchip Corp WARRANTYLIMITED WARRANTY Faroudja Laboratories