Meridian Audio FDP-DILA2 Turning on the Power, Turn on the MAIN POWER switch, Remote control unit

Page 31

Basic Operations

Basic Operations

■Projector’s buttons

STAND BY

LAMP TEMP

	OPERATE
HIDE
	PC
KEYSTONE
	VIDEO
PRESET	MENU
EXIT	ENTER

STAND BY indicator

OPERATE indicator OPERATE button

The following describes the basic procedure for normal use of the projector.

1. Turning on the Power

1 Turn on the MAIN POWER switch.

ON [ ❙ ]:The main power turns on and the STAND BY indicator comes on.

Projector’s indicator

STAND BY

OPERATE

2Press the OPERATE button for one second or more.

•The OPERATE indicator lights and the projected screen slowly appears.

Remote control unit

Projector

OPERATE

STAND BY

or

Notes

OPERATE

■Remote control unit

QUICK

ALIGN.OPERATE

HIDE

W

SCREEN FREEZE COMP VIDEO

S

PC1 PC2 DVI Y/C

T T

KEYSTONE DIGITAL ZOOM FOCUS

ZOOM

W W

PRESETMENU

EXITENTER

RM-M160 REMOTE CONTROL UNIT

• After the power is turned on, the image may be jumbled for a few seconds, but this is not a malfunction.

• After the indicator comes on, it can take a minute or so for the lamp to warm up and operate consistently.

■ Turning off the Power

1Press the OPERATE button for one second or more.

•The STAND BY indicator changes to blinking, and the projector goes into cool-down mode. The cool-down

mode will continue for approximately 120 seconds.

Remote control unitProjector (Blinking)

OPERATE button

OPERATE	STAND BY
	OPERATE

Note

•The OPERATE button will not work for approximately 1 minute from when the light-source lamp is turned on. Use the button after approximately 1 minute.

2Turn off the MAIN POWER switch after the STAND BY indicator changes to

steady on.

OFF [‡]:The MAIN POWER switch turns off and the

STAND BY indicator goes off.

Projector

STAND BY

OPERATE

CAUTION

•Do not turn off the MAIN POWER switch during cool-down mode (the STAND BY indicator blinking). Turn it off after the STAND BY indicator becomes on (stand-by mode).

31

Image 31

Contents Home Theater Optimized Installation and Operations ManualFDP-DILA2 About burning-inof the D-ILAdevice SAFETY PRECAUTIONSIMPORTANT INFORMATION IMPORTANT SAFEGUARDS About the installation placePower cord Contents for checking operation Accessoriesfor Macintosh 1Exhaust vents Controls and Features3AC IN power input terminal 5MAIN POWER switcheControl panel Controls and FeaturespConnector panel wAir inletyOpening for replacing the light-sourcelamp Controls and Featurest y u tAir inlet filterControl Panel on the Projector rTEMP indicator Controls and FeaturespPRESET button eLAMP indicator4 PC computer 2 input terminals BNC ⋅ Controls and Features1PC computer 1 input terminal D-sub 3-row15 pin 3DVI terminal DVI-D24 pinRemote Control Unit ySCREEN W/S buttons Controls and FeaturesrDIGITAL ZOOM T/W buttons tPC buttonsOpen the back cover Install the batteriesPrecautions for using batteries Controls and FeaturesPrecautions for Installation Installing the ProjectorCAUTIONS Leveling the projector Adjusting the Inclination of the ProjectorAdjusting the vertical angle of the projector Installing the ProjectorTop view Installing the Projector against the ScreenInstalling the Projector Side viewProjection Distance and Screen Size Installing the ProjectorOptional Lenses 4Tighten the SHIFT LOCK fixing bolt firmly Installing the Projector2Loosen the SHIFT LOCK fixing bolt screenInstalling the Projector Using as a wireless remote control unitInstalling the Projector When installing adjusting/setting the unitCAUTIONS Note: Instructions for installing the Video Connecting to Various DevicesVideo signals Computer signalsConnecting to Various Devices Allowable input signalsConnecting to Various Devices Connecting to Video DevicesMemo Connecting to Various Devices Connecting to HDTV Devices/DVD PlayersMemo Connecting to Various Devices Connecting to Devices which Control the ProjectorConnecting to Various Devices Connecting to Computer DevicesConnection to an IBM PC or IBM-compatiblecomputer 2 Wind the cord around the ferrite core Connecting to Various Devices1Release the stopper at each end and open the ferrite coreConnecting the Power Cord Lamp control settings Basic OperationsTurning off the Power 1. Turning on the Power1 Turn on the MAIN POWER switch Remote control unitProjector’s buttons Remote control unitRemote control unit Remote control unit5. Setting the Screen Aspect Ratio 3. Adjust the Screen Size ZoomingRemote control unit 4. Adjust FocusRemoving the Trapezoidal Distortion of the Image Remote control unitProjector’s buttons Turning off Image HIDEQuick Alignment Function QUICK ALIGN Remote control unitBasic Operations Basic Operations Remote control unitDisplaying a Still Picture FREEZE Zooming a Part of the Image DIGITAL ZOOM T/WMenu Transition Diagram in No signal Menu Mode Menu OperationsQuick Reference Guide for No signal Menu Mode Menu Operations Menu Transition Diagram in Video Menu ModeMenu Operations Quick Reference Guide for Video Menu ModeFactory set value Menu Operations Menu Transition Diagram in PC Menu ModeMenu Operations Quick Reference Guide for PC Menu Mode1Press the MENU button or adjust the value4Press the cursor button 5 or ∞ to select an item in the submenuPC menu mode Remote control unitProjector Video menu mode1Press the MENU button Changing the Color System Video Menu Mode Only1Press the MENU button Changing the Language Display1Press the MENU button 3Set the language with the cursor button 5 or ∞Menu Operations Adjusting Tracking/PhaseAdjust the tracking or phase with the cursor 2 or 1Press the MENU button1Press the MENU button installations may be required Make adjustment with the cursor 2 orTo perform All Reset However, some fine-tuningfor specificbutton Adjusting Color temperatureTo perform All Reset 1Press the MENU button1Press the MENU button Adjusting the Video Screen/Menu Positionmenu 1Press the MENU button 1Press the MENU button Menu Operations Setting and Adjusting Other Functions OPTIONSMake adjustment with the cursor 2 or 1Press the MENU buttonMenu Operations Menu Operations Getting Information1Press the MENU button 3Press the MENU button to exit the menu mode2Loosen the fuse holder to remove it Replacing the Fuse5Reinstall the fuse holder into the projector the projector and the wall outletLight-sourcelamp and lamp use time Replacing the Light-SourceLampCAUTIONS Replacing the Light-SourceLampLoosen the two screws with a flat-endscrewdriver inside and fasten the screws 4Replace the lamp-replacementopening5Reset the lamp use time 3 Insert the new light-sourcelamp fullyinto stand-bymode Resetting the Lamp Use Time1Turn on the MAIN POWER switch to go Projector’s button4Reinstall the filter Cleaning and Replacing the Filter Cover1Turn off the MAIN POWER switch 3Clean the filterTroubleshooting Troubleshooting MaintenanceAction to be taken for warning indication Warning IndicationCorrective action Warning MessagesMessage CauseWarning Messages Warning Messages Displayed when the lamp controlMemo Input terminals SpecificationsOptical mechanism system Electrical systemGeneral Specifications22.430 SpecificationsFront SidePC1 terminal/PC OUT terminal SpecificationsY/C terminal RS-232Cterminal1. Communication Specifications RS-232Cexternal control2. Command Format 1 Numeric value 3. Control command table2-3Parameters used for the data format RS-232Cexternal controlFor lens unit GL-M2910G1 AppendixFor lens unit GL-M2915SG1.5 For lens unit GL-M2920ZG2 to AppendixFor lens unit GL-M2930SZG2.9 to Page Page Page A Division of Genesis Microchip Corp WARRANTYLIMITED WARRANTY Faroudja Laboratories