Husqvarna WG4815E, WG3613E manual Checking the Oil Level

Page 50

LUBRICATION

Checking the Oil Level

Check the oil level in the engine when the machine is standing level and the engine is stopped.

Remove the dipstick, wipe it clean, and then replace it.

The dipstick should not be screwed into place.

Take the dipstick out again and read the oil level.

The oil level should lie between the markings on the dipstick. If the level is approaching the ”ADD” mark, fill with oil to the ”FULL” mark on the dipstick.

Never fill above the ”FULL” mark.

The oil is filled through the hole for the dipstick.

Use engine oil SAE 30 or SAE 10W-30 or, alternately, 10W/40, class SF–SJ

(over +32 °F / 0 °C).

Over +68 °F /+20 °C SAE 40 can be used.

Use engine oil SAE 5W-20, class SF–SJ (under +32 °F / 0 °C).

The engine holds 1.6 qt (1.5 liters) of oil excluding the filter (including filter 1.8 qt, 1.7 liters).

8011-452

Remove the dipstick

8009-159

The dipstick markings

8009-140

Engine oils

English-48

Image 50

Contents WG4815E/968999120 WG3613E/968999117 Page OPERATOR’S Manual Mower WG3613E WG4815EEnglish-2 Introduction IntroductionGood Service Manufacturing NumberXxxxxxx xxxx xxxxxxxx xxx Xxxx xxxxxx Symbols and DecalsSymbols and Decals Keep a safe General Use Safety InstructionsSafety Instructions Age of the user Do not Driving on SlopesDo as follows Children Maintenance Use protective glasses at maintenance work Transport Customer responsibilitiesControl Locations ControlsControls Ignition Switch Recoil Starter GripMotion control levers Operator Presence LeversParking Brake Gear shift leverNeutral Bail Blade Engagement Lever USE Full Throttle When Mowing , forThrottle Control and Choke Control Choke ControlRefueling Close fuel valve at the end of each mowing job AccessoriesFuel Shut-off Valve Before Starting OperationOperation Starting the Engine Fuel shut-off valve, Open Presence lever Gearbox RunningMowing Tips ReversingTo operate on hills Mowing patterns Normal operating stop StoppingEmergency stop Stopping the Engine Adjustment of cutting height It may be necessary to readjust drive and brake linkagesSpacers Height Caster arm Under cutter Housing Cutting height table Axle Spacers Blade PositionAxle Spacers Blade Cutting Position Moving machine by Hand Maintenance Schedule MaintenanceMaintenance 300 Ignition System Checking the Safety System Functional checkChecking and Adjusting Throttle and Choke Cable Checking the Engines Cooling Air IntakeReplacing the Air Filter Checking Tire Pressures Replacing the Fuel FilterChecking the Fuel Pump’s Air Filter Deck belt Checking the Parking BrakeChecking the V-belts Under side of rear deck Brake Rod AdjustmentChecking the Blades Hardware Cleaning and WashingCaster Wheels Blade replacement Lubrication Schedule LubricationLubrication Front Wheel Mount Lubricating the CablesLubricating in Accordance with the Lubrication Schedule Front Wheel BearingsChanging the Oil Filter Engine oil Changing the Engine OilChecking the Oil Level Mower deck lever Drive wheel idle arm, right and leftCoupling Rear wheel Problem Cause Trouble Shooting GuideTrouble Shooting Guide English-52 Storage ServiceStorage Winter StorageWiring Diagrams Wiring diagramsWG3613E WG4815E Technical DataTechnical data Torque Specifications Overall dimensionsConformity Certificates USA requirementsDelivery Service Service JournalService Journal After the First 8 HoursHour Service English-60 English-61 English-62 At Least Once Each Year 106457R0108/11/05