Manuals / 3M / Computer Equipment / Tablet Accessory

3M 800r3 manual Special Set-Up Procedure Continued, 2 - Column Re-Positioning

Models: 800r3

1 72

Download 72 pages 8.81 Kb

Page 30

Image 30

Special Set-Up Procedure (Continued)

Figure 5-2 – Column Re-Positioning

3.Actuate raising switch to release upper assembly latch. (Upper assembly will rest on blocks.) Turn off and disconnect air supply.

4.Remove plastic plugs and M8 x 20 socket head capscrews from (A) and (B) in one side column (4 each). Slide side column up approximately 110 mm [4.25 in] and re-install capscrews in (B) and (C). DO NOT TIGHTEN SCREWS. Repeat procedure for other side column.

5.Using carpenters square, line up column perpendicular to machine bed as shown in Figure 5-2B. Tighten capscrews and install plastic plugs. Repeat this procedure for both columns.

6.Connect and turn on air supply, actuate raising switch and latch upper assembly in full up position.

7.Remove blocking, unlatch and lower upper assembly.

Page 30

Image 30

3M 800r3 manual Special Set-Up Procedure Continued, 2 - Column Re-Positioning

Contents

3M-Matic Instructions and Parts ListSafeguards AccuGlideTM3M/Tape Dispenser Parts Replacement Parts and Service InformationTo Our Customers 241 Venture DriveTo Our Customers Replacement Parts And Service InformationSERVICE, REPLACEMENT PARTS AND ADDITIONAL MANUALS AVAILABLE DIRECT FROMSection I - 800r3 Random Case Sealer 800r3 Random Case Sealer, TypePage This instruction manual is divided into two sections as followsSee Section II for Table of Contents Table of Contents ContinuedReplacement Parts Illustrations and Parts Lists PageIntended Use 3M-MaticTM 800r3 Random Case Sealer, Type800r3 Contents Figure 1-1 - Knife Warning Label Important SafeguardsThis safety alert symbol identifies important messages in this manual Figure 1-2 - Electrical Warning LabelFigure 1-6 - Safety Instructions Label Important Safeguards ContinuedFigure 1-5 - Safety Instructions Label Figure 1-4 - Stop and On/Off LabelsFigure 1-8 - Raise/Latch Upper Assembly Label Figure 1-9 - Force Adjustment LabelFigure 1-10 -Air Pressure Gage Label The Tape Threading Label, shown in Figure 1-12 - Tape Threading Label Figure 1-11 - Knife Warning Label3. Operating Conditions 1. Power Requirements2. Operating Rate 4. TapeBox Size Specifications Continued9. Box Weight and Size Capacities Weight DETERMINE THE BOX LIMITATIONS BY COMPLETING THIS FORMULA10. Machine Dimensions MinimumMaximum Machine Set-Up Installation and Set-UpReceiving And Handling CAUTION - Machine weighs approximately 208 kg 460 pounds uncratedInstallation and Set-Up Continued WARNING - Use care when working with compressed air Figure 2-2 - Pneumatic ConnectionOperation Figure 3-1 - Case Sealer ComponentsFigure 3-2 - Controls, Valves and Switches 1 Electrical On/Off Switch Operation Continued2 Main Air On/Off Valve/Pressure Regulator/ Filter - Figure 6 Centering Switch, Box Drive Belts Figure 3-3 - On/Off Valve/Regulator/Filter 3 E-Stop SwitchWARNING - The E-Stop switch or door must not be used for raising 4 Door9 Air Pressure Regulator, Upper Taping Head Frame -Figure 12 Indicator, Air PressureFigure 3-5 - Air Regulator, Upper Taping Head Frame 10 Main Air Pressure Gauge4. Keep hands and loose clothing away from moving belts 2. Turn electrical and air supply off when machine is not in useWARNINGS Tape Loading/ThreadingFigure 3-7 - Operation Figure 3-8 - Operation 8888 - Operation WARNING - Keep hands away from drive belts when feeding boxes toBox Sealing Box JamCleaning MaintenanceWARNING - Turn off electrical and air supplies and disconnect power Lubricationpersonnel could result WARNING -The E-Stop switch or door must not be used for raisingWARNING - Each drive assembly weighs approximately 20.4 kg Drive BeltsFigure 4-3 - Box Drive Assembly, Infeed End Figure 4-4 - Box Drive Belt Tension Adjustment, Top Viewpersonnel could result WARNING - The following procedure must be performed byKnife Replacement, Taping Head Circuit BreakerAdjustments Taping Head Adjustments - Refer to Sectionpersonnel could result Drive Belt Tension WARNING -The E-Stop switch or door must not be used for raising WARNING - Turn air supply and electrical power off and disconnectWARNING - Use care when working near taping head knives as knives Changing the Tape Leg Length From 70 to 50 mm 2.75 to 2.00 inSpecial Set-Up Procedure Continued Figure 5-2 - Column Re-PositioningTHIS PAGE IS BLANK Problem TroubleshootingTroubleshooting Guide CauseProblem Troubleshooting ContinuedTroubleshooting Guide Cause800r3 Case Sealer Operating Sequence Electrical/Pneumatic Diagrams WARNING - Electrical service procedures must be performed byFigure 6-1 - Electrical Diagram Page Electrical/Pneumatic Diagrams Continued Figure 6-2 - Pneumatic DiagramWARNING - Turn off and disconnect air and electrical supplies before Page THIS PAGE IS BLANK Section/Ref. No Parts Ordering/ServiceSpare Parts Part NumberOptions/Accessories Option/AccessoryPart Number Replacement Parts - Illustrations and Parts Lists 800r3 Random Case Sealer, TypeWith AccuGlide II STD 3 Inch Taping Heads THIS PAGE IS BLANK 800r3 Random Case Sealer Frame Assemblies 800r3 Random Case Sealer Description Ref. No3M Part No 4896-1800r3 Random Case Sealer Ref. No 3M Part NoDescription 800r3 Random Case Sealer Figure 5184/1 of 3M Part No Figure 5184 page 1 ofRef. No Description800r3 Random Case Sealer Figure 5184/2 of 3M Part No Figure 5184 page 2 ofRef. No Description800r3 Random Case Sealer Ref. No 3M Part NoDescription 800r3 Random Case Sealer Ref. No 3M Part NoDescription 800r3 Random Case Sealer Ref. No 3M Part NoDescription 800r3 Random Case Sealer Ref. No 3M Part NoDescription 800r3 Random Case Sealer Figure 7006/1 of 3M Part No Figure 7006 page 1 ofRef. No Description800r3 Random Case Sealer Figure 7006/2 of 3M Part No Figure 7006 page 2 ofRef. No Description800r3 Random Case Sealer Figure 7007/1 of 3M Part No Figure 7007 page 1 ofRef. No Description800r3 Random Case Sealer Figure 7007/2 of 3M Part No Figure 7007 page 2 ofRef. No Description800r3 Random Case Sealer Ref. No 3M Part NoDescription 800r3 Random Case Sealer Safety and Information Labels 3M Part No 800r3 Safety and Information LabelsRef. No Description