Manuals / 3M / Computer Equipment / Tablet Accessory

3M 800r3 manual Electrical/Pneumatic Diagrams, 1 - Electrical Diagram

Models: 800r3

1 72

Download 72 pages 8.81 Kb

Page 35

Image 35

Electrical/Pneumatic Diagrams

WARNING – Electrical service procedures must be performed by

a qualified electrical technician. Turn off and disconnect electrical and pneumatics before servicing unit. High voltage inside electrical enclosure can cause severe injury or death.

Figure 6-1 – Electrical Diagram

Page 35

Image 35

3M 800r3 manual Electrical/Pneumatic Diagrams, WARNING - Electrical service procedures must be performed by

Contents

AccuGlideTM Instructions and Parts ListSafeguards 3M-Matic241 Venture Drive Replacement Parts and Service InformationTo Our Customers 3M/Tape Dispenser PartsAVAILABLE DIRECT FROM Replacement Parts And Service InformationSERVICE, REPLACEMENT PARTS AND ADDITIONAL MANUALS To Our CustomersThis instruction manual is divided into two sections as follows 800r3 Random Case Sealer, TypePage Section I - 800r3 Random Case SealerPage Table of Contents ContinuedReplacement Parts Illustrations and Parts Lists See Section II for Table of Contents3M-MaticTM 800r3 Random Case Sealer, Type Intended Use800r3 Contents Figure 1-2 - Electrical Warning Label Important SafeguardsThis safety alert symbol identifies important messages in this manual Figure 1-1 - Knife Warning LabelFigure 1-4 - Stop and On/Off Labels Important Safeguards ContinuedFigure 1-5 - Safety Instructions Label Figure 1-6 - Safety Instructions LabelFigure 1-10 -Air Pressure Gage Label Figure 1-8 - Raise/Latch Upper Assembly LabelFigure 1-9 - Force Adjustment Label Figure 1-12 - Tape Threading Label Figure 1-11 - Knife Warning Label The Tape Threading Label, shown in4. Tape 1. Power Requirements2. Operating Rate 3. Operating ConditionsDETERMINE THE BOX LIMITATIONS BY COMPLETING THIS FORMULA Specifications Continued9. Box Weight and Size Capacities Weight Box SizeMaximum 10. Machine DimensionsMinimum CAUTION - Machine weighs approximately 208 kg 460 pounds uncrated Installation and Set-UpReceiving And Handling Machine Set-UpInstallation and Set-Up Continued Figure 2-2 - Pneumatic Connection WARNING - Use care when working with compressed airFigure 3-1 - Case Sealer Components Operation2 Main Air On/Off Valve/Pressure Regulator/ Filter - Figure Figure 3-2 - Controls, Valves and Switches 1 Electrical On/Off SwitchOperation Continued 4 Door Figure 3-3 - On/Off Valve/Regulator/Filter 3 E-Stop SwitchWARNING - The E-Stop switch or door must not be used for raising 6 Centering Switch, Box Drive Belts10 Main Air Pressure Gauge 12 Indicator, Air PressureFigure 3-5 - Air Regulator, Upper Taping Head Frame 9 Air Pressure Regulator, Upper Taping Head Frame -FigureTape Loading/Threading 2. Turn electrical and air supply off when machine is not in useWARNINGS 4. Keep hands and loose clothing away from moving beltsBox Jam WARNING - Keep hands away from drive belts when feeding boxes toBox Sealing Figure 3-7 - Operation Figure 3-8 - Operation 8888 - OperationLubrication MaintenanceWARNING - Turn off electrical and air supplies and disconnect power CleaningDrive Belts WARNING -The E-Stop switch or door must not be used for raisingWARNING - Each drive assembly weighs approximately 20.4 kg personnel could resultFigure 4-4 - Box Drive Belt Tension Adjustment, Top View Figure 4-3 - Box Drive Assembly, Infeed EndCircuit Breaker WARNING - The following procedure must be performed byKnife Replacement, Taping Head personnel could resultpersonnel could result Drive Belt Tension AdjustmentsTaping Head Adjustments - Refer to Section Changing the Tape Leg Length From 70 to 50 mm 2.75 to 2.00 in WARNING - Turn air supply and electrical power off and disconnectWARNING - Use care when working near taping head knives as knives WARNING -The E-Stop switch or door must not be used for raisingFigure 5-2 - Column Re-Positioning Special Set-Up Procedure ContinuedTHIS PAGE IS BLANK Cause TroubleshootingTroubleshooting Guide ProblemCause Troubleshooting ContinuedTroubleshooting Guide Problem800r3 Case Sealer Operating Sequence Figure 6-1 - Electrical Diagram Electrical/Pneumatic DiagramsWARNING - Electrical service procedures must be performed by Page WARNING - Turn off and disconnect air and electrical supplies before Electrical/Pneumatic Diagrams ContinuedFigure 6-2 - Pneumatic Diagram Page THIS PAGE IS BLANK Part Number Parts Ordering/ServiceSpare Parts Section/Ref. NoPart Number Options/AccessoriesOption/Accessory With AccuGlide II STD 3 Inch Taping Heads Replacement Parts - Illustrations and Parts Lists800r3 Random Case Sealer, Type THIS PAGE IS BLANK 800r3 Random Case Sealer Frame Assemblies 800r3 Random Case Sealer 4896-1 Ref. No3M Part No Description800r3 Random Case Sealer Description Ref. No3M Part No 800r3 Random Case Sealer Figure 5184/1 of Description Figure 5184 page 1 ofRef. No 3M Part No800r3 Random Case Sealer Figure 5184/2 of Description Figure 5184 page 2 ofRef. No 3M Part No800r3 Random Case Sealer Description Ref. No3M Part No 800r3 Random Case Sealer Description Ref. No3M Part No 800r3 Random Case Sealer Description Ref. No3M Part No 800r3 Random Case Sealer Description Ref. No3M Part No 800r3 Random Case Sealer Figure 7006/1 of Description Figure 7006 page 1 ofRef. No 3M Part No800r3 Random Case Sealer Figure 7006/2 of Description Figure 7006 page 2 ofRef. No 3M Part No800r3 Random Case Sealer Figure 7007/1 of Description Figure 7007 page 1 ofRef. No 3M Part No800r3 Random Case Sealer Figure 7007/2 of Description Figure 7007 page 2 ofRef. No 3M Part No800r3 Random Case Sealer Description Ref. No3M Part No 800r3 Random Case Sealer Safety and Information Labels Description 800r3 Safety and Information LabelsRef. No 3M Part No