Manuals / 3M / Computer Equipment / Tablet Accessory

3M 800r3 manual personnel could result, Circuit Breaker, Determine cause of overload and correct

Models: 800r3

1 72

Download 72 pages 8.81 Kb

Page 27

Circuit Breaker

Maintenance (Continued)

WARNING – Turn off electrical and air supplies and disconnect power cord from electrical supply before beginning maintenance. If power cord is not disconnected, severe injury to

personnel could result.

Circuit Breaker

The case sealer is equipped with a circuit breaker which trips if the motors are overloaded. Located inside the electrical enclosure on the side of the machine frame just below the machine bed, the circuit breaker has been pre-set at 1.9 amps and requires no further maintenance.

WARNING – The following procedure must be performed by

trained service personnel because of the high voltage electrical hazard within the control box.

If circuit is overloaded and circuit breaker trips, unplug machine from electrical power:

1.Determine cause of overload and correct.

2.Remove electrical enclosure cover.

3.Press the red "Reset" button and then the green "Start" button.

4.Replace cover.

5.Plug in machine.

6.Press machine "On" button to resume case sealing.

Knife Replacement, Taping Head

See Section II, "Maintenance – Knife Replacement", page 9.

22

Image 27

3M 800r3 manual personnel could result, Circuit Breaker, WARNING - The following procedure must be performed by

Contents

AccuGlideTM Instructions and Parts ListSafeguards 3M-Matic241 Venture Drive Replacement Parts and Service InformationTo Our Customers 3M/Tape Dispenser PartsAVAILABLE DIRECT FROM Replacement Parts And Service InformationSERVICE, REPLACEMENT PARTS AND ADDITIONAL MANUALS To Our CustomersThis instruction manual is divided into two sections as follows 800r3 Random Case Sealer, TypePage Section I - 800r3 Random Case SealerPage Table of Contents ContinuedReplacement Parts Illustrations and Parts Lists See Section II for Table of Contents3M-MaticTM 800r3 Random Case Sealer, Type Intended Use800r3 Contents Figure 1-2 - Electrical Warning Label Important SafeguardsThis safety alert symbol identifies important messages in this manual Figure 1-1 - Knife Warning LabelFigure 1-4 - Stop and On/Off Labels Important Safeguards ContinuedFigure 1-5 - Safety Instructions Label Figure 1-6 - Safety Instructions LabelFigure 1-8 - Raise/Latch Upper Assembly Label Figure 1-9 - Force Adjustment LabelFigure 1-10 -Air Pressure Gage Label Figure 1-12 - Tape Threading Label Figure 1-11 - Knife Warning Label The Tape Threading Label, shown in4. Tape 1. Power Requirements2. Operating Rate 3. Operating ConditionsDETERMINE THE BOX LIMITATIONS BY COMPLETING THIS FORMULA Specifications Continued9. Box Weight and Size Capacities Weight Box Size10. Machine Dimensions MinimumMaximum CAUTION - Machine weighs approximately 208 kg 460 pounds uncrated Installation and Set-UpReceiving And Handling Machine Set-UpInstallation and Set-Up Continued Figure 2-2 - Pneumatic Connection WARNING - Use care when working with compressed airFigure 3-1 - Case Sealer Components OperationFigure 3-2 - Controls, Valves and Switches 1 Electrical On/Off Switch Operation Continued2 Main Air On/Off Valve/Pressure Regulator/ Filter - Figure 4 Door Figure 3-3 - On/Off Valve/Regulator/Filter 3 E-Stop SwitchWARNING - The E-Stop switch or door must not be used for raising 6 Centering Switch, Box Drive Belts10 Main Air Pressure Gauge 12 Indicator, Air PressureFigure 3-5 - Air Regulator, Upper Taping Head Frame 9 Air Pressure Regulator, Upper Taping Head Frame -FigureTape Loading/Threading 2. Turn electrical and air supply off when machine is not in useWARNINGS 4. Keep hands and loose clothing away from moving beltsBox Jam WARNING - Keep hands away from drive belts when feeding boxes toBox Sealing Figure 3-7 - Operation Figure 3-8 - Operation 8888 - OperationLubrication MaintenanceWARNING - Turn off electrical and air supplies and disconnect power CleaningDrive Belts WARNING -The E-Stop switch or door must not be used for raisingWARNING - Each drive assembly weighs approximately 20.4 kg personnel could resultFigure 4-4 - Box Drive Belt Tension Adjustment, Top View Figure 4-3 - Box Drive Assembly, Infeed EndCircuit Breaker WARNING - The following procedure must be performed byKnife Replacement, Taping Head personnel could resultAdjustments Taping Head Adjustments - Refer to Sectionpersonnel could result Drive Belt Tension Changing the Tape Leg Length From 70 to 50 mm 2.75 to 2.00 in WARNING - Turn air supply and electrical power off and disconnectWARNING - Use care when working near taping head knives as knives WARNING -The E-Stop switch or door must not be used for raisingFigure 5-2 - Column Re-Positioning Special Set-Up Procedure ContinuedTHIS PAGE IS BLANK Cause TroubleshootingTroubleshooting Guide ProblemCause Troubleshooting ContinuedTroubleshooting Guide Problem800r3 Case Sealer Operating Sequence Electrical/Pneumatic Diagrams WARNING - Electrical service procedures must be performed byFigure 6-1 - Electrical Diagram Page Electrical/Pneumatic Diagrams Continued Figure 6-2 - Pneumatic DiagramWARNING - Turn off and disconnect air and electrical supplies before Page THIS PAGE IS BLANK Part Number Parts Ordering/ServiceSpare Parts Section/Ref. NoOptions/Accessories Option/AccessoryPart Number Replacement Parts - Illustrations and Parts Lists 800r3 Random Case Sealer, TypeWith AccuGlide II STD 3 Inch Taping Heads THIS PAGE IS BLANK 800r3 Random Case Sealer Frame Assemblies 800r3 Random Case Sealer 4896-1 Ref. No3M Part No Description800r3 Random Case Sealer Ref. No 3M Part NoDescription 800r3 Random Case Sealer Figure 5184/1 of Description Figure 5184 page 1 ofRef. No 3M Part No800r3 Random Case Sealer Figure 5184/2 of Description Figure 5184 page 2 ofRef. No 3M Part No800r3 Random Case Sealer Ref. No 3M Part NoDescription 800r3 Random Case Sealer Ref. No 3M Part NoDescription 800r3 Random Case Sealer Ref. No 3M Part NoDescription 800r3 Random Case Sealer Ref. No 3M Part NoDescription 800r3 Random Case Sealer Figure 7006/1 of Description Figure 7006 page 1 ofRef. No 3M Part No800r3 Random Case Sealer Figure 7006/2 of Description Figure 7006 page 2 ofRef. No 3M Part No800r3 Random Case Sealer Figure 7007/1 of Description Figure 7007 page 1 ofRef. No 3M Part No800r3 Random Case Sealer Figure 7007/2 of Description Figure 7007 page 2 ofRef. No 3M Part No800r3 Random Case Sealer Ref. No 3M Part NoDescription 800r3 Random Case Sealer Safety and Information Labels Description 800r3 Safety and Information LabelsRef. No 3M Part No