Configuring Voice Support Config, Call Control | ADTRAN 600 Series

Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B

Page 47

Configuring Voice Support – Config

Use the 2 menu to view and set the parameters shown in Figure 15.

Figure 15. Voice/Config Menu

>Call Control

The !!! setting is used to configure the correct Voice Gateway protocol for voice signaling control be- tween the Total Access 600 and the configured Gateway. The !!! setting must be configured correctly before the voice circuits will work correctly. The Total Access 600 supports Jetstream, Tollbridge, and CopperCom Voice Gateways.

>VPI

The 1 setting is used to configure the Total Access 600 virtual path setting used to communicate with the configured Voice Gateway.

>VCI

The setting is used to configure the Total Access 600 virtual circuit setting used to communicate with the config- ured Voice Gateway.

© 2002, ADTRAN, Inc.

Total Access 600 Series User Manual

Image 47

ADTRAN 600 Series user manual Configuring Voice Support Config, Call Control

Contents

Total Access 600 Series Shdsl IAD To the Holder of the Manual Trademarks Safety Instructions 2002, ADTRAN, Inc 2002, ADTRAN, Inc 2002, ADTRAN, Inc Limited Product Warranty Warranty and Customer Service Pre-Sales Inquiries and Applications Support Customer Service, Product Support Information, and TrainingRepair and Return Training Installation and Maintenance SupportPost-Sale Support Total Access 600 Series Shdsl IAD User Interface Guide +@A1 +@&.&$$ +@,%.% @/& % @/& %.&$$ @.&$$ @/1 @.%+0% %B,% ##%B 8= $*+*$&,$&-# # #$% Figures Analog Lifeline Firmware Updates Voice Over DSL Overview Voice over DSL System Info Firmware Revision Bootcode RevisionPart Number Serial Number Telnet User List System ConfigNetwork Timing Mode Telnet Access Level Password ProtectInstructions for Changing Passwords Step Action Maint Port Menu Network Time System Utility Upgrade Firmware Config Transfer Ping Layer One Interface Configuring WAN SettingsATM Config Dslam Type Data Scrambling ATM Stats AP Receive Cells Discarded AP Receive Cell ErrorsAP Rx Cells AP Rx OAM Cells AAL5 No Data Packets AAL5 Receive ErrorsAAL5 Receive Discarded Frames AAL5 No ATM Frames Global Configuring the Router Configuration Text string used to represent the domain name Bridge Dotted decimal format Security 2002, ADTRAN, Inc Ethernet Menu Ethernet MAC Address Use this menu to enable RIP on the LAN interface WAN This selection enables IP on this PVC PPPoATM RFC 1483 Bridge This is the username used to authenticate the PPP peer Only routes not learned on the WAN connection This is the PPP encapsulation. LLC or VC-Mux Router/Status Menu Configuring the Router Status Configuring the Router Logs Network Log Sys log HostPPP Log Connection Log Call Control Configuring Voice Support Config Pots Stats Configuring Voice Support StatusGateway Stats PVC Stats Test Managing the Modules ModulesMenu FXS Mode Managing the Modules V.35 SetupConfiguration Following settings are used for FRF5 Following settings are used for FRF8 Updating Firmware via a Forced Download Appendix A. Updating Total Access 600 Firmware using Xmodem Press $until a menu appears Select -# # for #9 When prompted, press to erase flashUpdating Firmware via the Console Menus Appendix B. Updating Total Access 600 Firmware using Tftp Message Meaning Message Meaning System Time Status Bar ModeMenu Path Left Pane Right Window Pane Notation Window Pane Navigation Navigating Using the Keyboard Keys Additional Terminal Menu Window Features Session Management Keystrokes Getting Help Application Diagram Voice Turn Up Step Action Appendix E. RFC1483 Quick Start IP Routing IP Routing Step Action Options Appendix F. RFC1483 Quick Start IP Routing with NAT Bridging Step Action Appendix G. RFC1483 Quick Start Bridging Appendix H. Craft Port Connection Pin-out 2002, ADTRAN, Inc