Manuals / ADTRAN / Computer Equipment / Network Card

ADTRAN 61200051L1, 1200051L6, 1200051L2 Maintenance Interface, VT 100 Maintenance Help Screen

Models: 1200051L2 1200051L5 1200051L1 1200051L6 61200051L1

1 165

Download 165 pages 47.6 Kb

Page 29

Image 29

Chapter 3. Installation

MAINTENANCE INTERFACE

The Maintenance interface is available at 9600 bps, 8 data bits, no parity, no ﬂow control, asynchronous format through the Mainte- nance port. See Connector Pinouts on page 119 for the pinout of the Maintenance port. A VT 100 terminal or null modem can be connected to the Maintenance port using an EIA-232 cable. This interface can be used to set internal S-registers, dial ISDN connec- tions, and disconnect calls. This port also allows ADTRAN Tech- nical Support personnel to retrieve vital information from the unit if a problem is encountered during initial conﬁguration of the ISU 2x64. Most problems can be solved without resorting to this port for assistance.

The ISU 2x64 Maintenance Help Screen can be activated by typ- ing !? at either the DTE#1 or DTE#2 prompt. The screen is shown in Figure 3-1.

Figure 3-1

VT 100 Maintenance Help Screen

61200051L1-1D

ISU 2x64 Dual Port ISDN Service Unit User Manual

15

Image 29

ADTRAN 61200051L1, 1200051L6, 1200051L2, 1200051L5 user manual Maintenance Interface, VT 100 Maintenance Help Screen

Contents

Part Numbers ISU Dual Port Isdn Service Unit Trademarks Isdn Page Canadian Emissions Requirements Canadian Equipment Limitations Table of Contents Software Version SAP Fallback Txinit Txfa TXADD01 Txdeq Tanull TcidDSU 57.6 Async 109 List Figure E-1 EIA-232 Interface 119 List of Tables Viii Adtran ISU Isdn Overview ISU 2x64 Rear Panel Indicator Deﬁnition DTE Indicators ISU 2x64 Front Panel ISU 2X64 InteroperabilityISU 2X64 Single Port Operation ISU 2x64 Interoperability DTE#2 Recommended Operating Protocols Call Type Protocol Sync Rates Supported bps Async Recommended Operating Modes Understanding Isdn and the ISU Isdn Ordering Codes Chapter Isdn Service Capability R previously Generic Data Capability S previously Generic Data M Capability C previously Generic Data C B1 previously Generic Data BI2 previously Generic Data I-1DN J3 previously Generic Data J-1DN M5 previously Generic Data M-1DN J2 previously Generic Data J Network Connection Chapter Installation DTE Data Connection VT 100 Maintenance Help Screen Maintenance Interface Dial Interface Connection Menu Navigation Chapter Operation Current Status Menu Front Panel DTE Indicators Getting Started VT 100 Menu Support Status Buffer VT 100 Status Screen Status Screen VT 100 Configuration Screen Configuration Screen VT 100 Test Menu Screen Chapter TestingTest Options Loopback Network Loopback DTELoopback Protocol Test Menu Tree Test Remote Loopback DisableLoopback Remote Software Version NEBE/FEBELoopback Both DTEs Test 2047 Both Dial Line Menu Tree Chapter ConfigurationDial Line Operation VT 100 Configuration Menu Screen Setting the Switch Protocol =AT&T 5ESS LCD Configuration Menu Tree Cofiguration Setting the Call Type Smart Dial Strings Setting the Terminal ID Setting the Busy Out Port Setting the Dial Options Dial Options, RS-366 Menu Tree =CONFIG AT Commands Example ATI1 Example ATSS80? =V.25 Dial Options, V.25 bis Menu Tree Dial Line, Auto Answer Menu Tree =CONFIG Bis Async Menu Tree Data Bits Menu Tree Setting Auto Answer Setting Answer Tone =Dial Line =Netw. options Answer Tone Menu Tree Setting Call Screening Setting Connect TimoutConnect Timout Menu Tree Call Screening Menu Tree SBus Termination Menu Tree SBus Termination Leased Line Menu Tree Leased Line ServiceClock mode Slave/Master Leased Application with Channel Banks Channel RateLimited Distance Modem Applications SBus Termination Synchronous DTE Options Menu Tree DTE Options for Asynchronous and Synchronous OperationAsynchronous DTE Options Menu Tree Bit Rate DTR Options Data Format Menu Tree Flow Control Menu Tree Transmit Clock Menu Tree Autobaud Protocol Menu Tree Setting Protocol Options Clear Channel =BONDING mode Protocol BONDING, Mode 1 Menu Tree Txdeq DSU 57.6 Async Call Type Rate Adaption Protocols Typical Units Supported Rate Adaptation Protocols PPP Menu Tree Point-to-Point Protocol PPP Front Panel Dialing Options Chapter Dial OptionsVT 100 Dial Options Screen Dial Menu Tree Dial number Hang up lineRedial last # Answer Call Quick Setup Menu Tree Chapter Quick SetupQuick Setup Configuration Quick Setup Data protocol Bonding mode DTE mode Asynchronous Protocol Bonding mode DTE mode Asynchronous Leased Line Second AT&T 5ESS Quick Setup Security Menu Tree Security Remote Config Set PasswordRemote Config Menu Tree Lock Keypad Lpbk remote 2B Cfg. Rmt. UnitLpbk remote 1B Security and Remote Configuration If The ISU 2x64 Does Not Read Ready Chapter TroubleshootingIf Self Test Fails Troubleshooting Troubleshooting Troubleshooting Troubleshooting Troubleshooting If the Wrong DTE Port Answers a Call If you Cannot Connect Calls Troubleshooting Calls Chapter Specifications Only available on part numbers 1200051L5 and 1200051L6 High x 8.75 wide x 11.00 deep, 3 lbs Specifications Appendix a AT Commands Carrier Detect CD Control Line Options DTE Data Type Options 5ESS Isdn U-Interface Operational Mode Options Appendix a AT Commands Appendix B Current Status Messages ISU is receiving its first TEI from the network Unit is ready to make or accept a call DSU 57.6 Async rate adaptation protocol Appendix C Status Buffer Messages Call control error Called number is busy Called number is out of order Facility requested cannot be provided by the network Invalid message, protocol error Bonding negotiation has failed Number dialed has been changed Local DTE invalid S-register setting Phone number dialed does not exist Register List Appendix DAuto Answer Character Is set LOW Layer Comp S26.......DTE Rate AdjustNumber = Locd DTE CDDTE DTR DTR = Bisync = NEC S52.......SWITCH Type Type Dial Mode= Fallback = PPP Channel Rate DTE ModeSPID1 LOC SPID2 LOC DTE DTE FlowDCE DTE Clock 118 EIA-232 Interface Appendix E Interface RS-530 ST-B RS-366 Interface PIN RJ-45 Dial Line Connector U Interface Maintenance Connector RJ-45 Dial Line Connector S/T Interface 124 Appendix F Ordering Isdn Without IOCs Isdn Service Ordering Information for the Adtran ISU 127 TEI Physical Interface Local ServiceLocal Interface Requirements 5ESS Custom Line Additional Parameters Long Distance ServiceDeciding What Services to Order 5ESS Features DMS-100 Protocol Version 1 Line Additional Parameters DMS Features Setting UP the ISU 2X64 for a NEW Line After Service Is Installed 134 Acronyms PRI Asynchronous transmission Glossary Ccitt DDS Isdn NT1 TE1 2B+D 144 Numerics Index 146 Isdn 123 Txdeq Txfa Txinit 150 Product Support Information