Advantech IPPC-9120, IPPC-9150 - page 16

General Information

• Introduction

• Specifications

• Dimensions

CHAPTER

1

Contents

Main Copyright notice Acknowledgments FCC Class B Packing List Packing List Additional Information and Assistance Safety Instructions Wichtige Sicherheishinweise Contents Page Page Page Page Figures Tables Page 1.1 Introduction 1.2 Specifications General Standard PC functions PCI SVGA/flat panel interface Audio function PCI bus Ethernet interface Analog Resistive Touchscreen (optional) NFI Touchscreen (optional) Optional modules Page Page Page System Setup 2.1 A Quick Tour of the IPPC-9120/9150 Series Page 2.1.1 PS/2 mouse and keyboard 2.1.2 Parallel port 2.1.3 Serial COM ports 2.1.4 VGA port 2.1.5 USB ports 2.1.6 Audio interface 2.1.7 Ethernet 2.1.8 Adjusting the LCD brightness 2.2 Installing SDRAM 2.3 Installing a CPU Page 2.4 Installing a 2.5" HDD Page Page 2.5 Installing a CD-ROM Drive Page Page 2.7 Mounting Instructions 2.7.1 Panel mounting Page Page Page Page Jumper Settings and Connectors 3.1 Jumpers and Connectors 3.1.1 Setting jumpers 3.1.2 Jumpers and switch IPPC-9120/9150 Series User's Manual 3.1.3 Locating jumpers and switch Figure 3-1: Locating jumpers on the IPPC-9120/9150 motherboard 3.1.4 Connectors IPPC-9120/9150 Series User's Manual 3.1.5 Locating connectors Figure 3-2: Locating connectors on the IPPC-9120/9150 motherboard 3.2 CPU Installation 3.3 COM-port Interface 3.3.1 COM2 RS-232/422/485 setting (JP3, JP4, JP5) 3.3.2 COM1 / COM2 pin 9 output type setting (JP9) Note: Pins 1, 3 and 5 are for COM1. Pins 2, 4 and 6 are for COM2. Chapter 3 Jumper Settings and Connectors 37 3.3.3 COM3 / COM4 pin 9 output type setting (JP6) 3.4 CMOS Clear for External RTC (JP8) Table 3-8: Clear CMOS / External RTC (JP8) *Normal operation Clear CMOS 3.5 Internal -12 V Source Enable Setting (JP1) 3.6 VGA Interface 3.6.1 LCD panel power setting 3.6.2 Panel type select (SW3) 3.7 Watchdog Timer Configuration 3.7.1 Watchdog activity selection (JP7) Page Page 4.1 Introduction 4.2 Installation of Ethernet Driver Page Page Page Page Page Page Page Page Page Page Page 5.1 Introduction 5.1.1 Chipset 5.1.2 Display memory 5.1.3 Display types 5.2 Installation of SVGA Driver Page Page Page Page Page Page Page Page Page Page Page Page Page 6.1 Introduction 6.2 Installation of Audio Driver Page Page Page Page Page Page Page 7.1 Introduction 7.2 Installation of PCMCIA Driver Page Page Page 8.1 Introduction 8.1.1 General information 8.1.2 Analog Resistive Touchscreen Specifications 8.1.3 NFI Touchscreen Specifications 8.2 Installation of Resistive-type Touchscreen Driver Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page 9.1 Award BIOS Setup 9.2 CMOS Setup Utility 9.3 Standard CMOS Setup 9.3.1 Hard disk configurations 9.4 BIOS Features Setup Page Page Page 9.5 Chipset Features Setup Page 9.6 Power Management Setup Page Page 9.7 PNP/PCI Configuration Setup 9.8 Load BIOS Defaults 9.9 Load Setup Defaults 9.10 Integrated Peripherals Page 9.11 Password Setting 9.12 IDE HDD Auto Detection 9.13 Save and Exit Setup 9.14 Exit Without Saving Page Page B B.1 Programming the Watchdog Timer Appendix B Programming the Watchdog Timer The following example shows how you might program the watchdog timer in BASIC: Page C Pin Assignments C.1 AT Power Connector (J1) C.2 TV Output Connector (J2) (*Reserved) C.3 Inverter Power Connector (J4) C.4 Internal Speaker Connector (J6) (*Reserved) C.5 Front Panel Control Connector (J8) (*Reserved) C.6 IR Connector (J9) (*Reserved) C.7 Flat Panel Display Connector (CN2) C.8 Flat Panel Display Connector (CN3) C.9 PanelLink Interface (CN4) (*Reserved) C.10 Floppy Drive Connector (CN10) C.11 Internal COM4, mouse and touch screen power connector (CN23) C.12 EIDE Hard Disk Drive Connector (CN16) # low active C.13 CD-ROM Connector (CN18) # low active C.14 CPU Fan Power Connector (FAN1) C.15 System Fan Power Connector (FAN2) Appendix C Pin Assignments C.16 PCI/ISA Bus Expansion Connector (SLOT1) side view Page Page Page Page C.17 COM2