Advantech MIC-3318

Software

Configuration

CHAPTER

Contents

Main Copyright Notice Acknowledgements CE Notification Product Warranty Packing List Technical Support and Sales Assistance Contents 1. Hardware Configuration.................... 1 2. Connecting Peripherals ....................17 3. Software Configuration ....................23 4. Award BIOS Setup ............................35 Page iix Figures Tables Page 1.1 Introduction 1.2 Specifications 1.2.1 Standard SBC functions 1.2.2 Display 1.2.3 Mechanical and Environmental Specifications Page Page 1.5 Jumper Settings 1.5.1 Assembling / Disassembling MIC-3318 1.5.2 Jumper Locations 1.5.3 Jumper Settings 1.5.4 CompactFlash master/slave selection(1F-JP5, pin 1,2) 1.5.5 Clear CMOS (JP1, pin 2,4,6) 1.5.6 Serial Ports (COM1 and COM2) Mode (RS-232/ 422/485) 1.6 Connectors Chapter 1 Hardware Configuration 13 Fig.1-6 Fig.1-7 Figure 1-6: MIC-3318 connector locations (1F) Figure 1-7: MIC-3318 connector locations (2F) Page 1.9 Installing SDRAM (SODIMMs) Page Page 2.1 IDE Device (2F-CN8, CN9) 2.2 CompactFlash Interface (1F-CN2) 2.3 VGA Display Connector (1F-CN7) 2.4 PS/2 Keyboard and Mouse Conn. (1F-CN1) 2.5 Serial Ports (2F-CN3, CN5, CN4, CN6) 2.6 Ethernet Configuration (2F-RJ1, RJ2) 2.7 USB Connector (1F-CN15, CN16) 2.8 Card Installation Page Page Page 3.1 Overview 3.2 Utilities and Drivers Intel Chipset Software Installation Utility VGA Drivers (Intel Extreme Graphics 2 Driver) IDE Drivers (Intel Application Accelerator) Intel Gigabit LAN 82540EM Drivers /Utility Page 3.3 USB driver 3.4 Watchdog Timer (WDT) Driver 3.4.1 Installing the Driver for the MIC-3318 Watchdog Timer Page Page Page Page Page Page Page 4.1 Introduction 4.2 Entering Setup 4.2.1 Standard CMOS Setup 4.2.2 Advanced BIOS Features Setup Page Page Page 4.2.3 Advanced Chipset Features Setup Page Page Page Page Page 4.2.5 Power Management Setup 4.2.6 PNP/PCI Configuration Setup Page Page Page Page A.1 Overview A.2 Programming the Watchdog Timer Page A.3 Example Programs 1. Enable watchdog timer and set 10 sec. as timeout interval Page 2. Enable watchdog timer and set 5 minutes as time- out interval Page 3. Enable watchdog timer to be reset by mouse Page 4. Enable watchdog timer to be reset by keyboard Page Page Page B.1 PS/2 Keyboard and Mouse Port (1F-CN1) B.2 CompactFlash Interface (1F-CN2) B.3 DB-15 VGA Port (1F-CN7) B.4 USB 1.1/2.0 Ports (1F-CN15 AND 1F-CN16) B.5 COMport (2F-CN3, 2F-CN5, 2F-CN4,2F- CN6) For front panel (2F-CN3 ,2F-CN5) For external connection to 3F (2F-CN4, 2F-CN6) B.6 Parallel Port (2F-CN7,2F-CN8) For front panel (2F-CN7) For external connection to 3F(2F-CN8) * low active B.7 Secondary IDE Connector for 2.5" HDD (2F-CN9, 2F-CN17) For direct installation (2F-CN9) For wiring out (2F-CN17) Page B.8 Gigabit LAN Port (2F-RJ1,2F-RJ2)