Alamo 1900 Pre-Deliveryservice, Check And Adjust Or Lubricate As Required, Mower, Safety Items

DEALER to CUSTOMER Pre-Delivery / Operation Instructions

Dealer should inform the Purchaser of this product of Warranty terms, provisions, and procedures that are applicable. Dealer should also inform the Purchaser to review the contents of the Operator’s Manual including safety equipment, safe operation and maintenance, to review the Safety Signs on the implement (and tractor if possible) and of Purchaser’s responsibility to train his/her operators in safe operation procedures.

•IMPLEMENTS: I have explained that Deflectors, Chain Guards, or Solid Skirts must be installed and maintained in good repair.

•DRIVELINES: I have made certain that all driveline, gearbox, and other shields are in good repair and fastened securely in place to prevent injuries from entanglement or thrown objects.

•HYDRAULIC MACHINES: I have explained the necessity of using clean hydraulic oil, changing filters as instructed, stopping leaks, damage caused by operating with over-heated oil, caring for hoses, using hoses of proper rating, maintaining the specified operating pressure and the potential hazard of oil’s penetrating the skin.

•FOLDING-TYPE IMPLEMENTS: I have explained that it is not possible to guard against thrown objects when the head is lifted off ground and that operator is responsible to watch out for persons in the area. I have explained that the lifted mower head or boom can contact overhead obstructions with damage to cables and telephone lines and possible injury. I have explained that the extended head or boom or retracted boom can contact power lines with resulting electrocution, injury or death and that operator is responsible for keeping clear of such hazards.

PRE-DELIVERY SERVICE

CHECK AND ADJUST OR LUBRICATE AS REQUIRED

See Operator’s Manual for Details

Inspection Performed - Warranty and Safety Procedures Explained - Installation Complete

LUBRICATION & HYDRAULICS	MOWER TO TRACTOR CONNECTIONS
 Gearbox (Oil Levels)		Draw Bar Length (Check And Set)
 Hydraulic Oil Level (External Tank)		A-Frame Pivot & Links
 Tractor Hydraulic Oil Level		Control Rods (Adjusted Equal)
 Hydraulic Hoses (Not Kinked Tighten Connections)		Axle Height (Adjusted)
 Front Pump Drive (Assembly Is Tight And Shaft Properly 		Cutting Height (Adjust)
Aligned)		Mount Kit-Pre-Operation Check Complete
MOWER		Mower Wing (Adjust Level With The Center)
 Spindle And Motor Bolts Properly Torqued		Mower Wing (Check For Proper Raising Operation)
		C.V. Drivelines (Check Max Turn Radius)
 Spindle Oil Level
		Pull Type Hitch (Height Adjustment)
 Blade Carrier Bolts Properly Torqued/Retaining Pin In
		Mounting Hardware Properly Torqued
Place	SAFETY ITEMS
 Mower Cutting Height And Level Adjusted
 Cutting Shaft Bearings Lubricated		Protective Shields (Operation And Installation)
 All Hardware Properly Torqued		Driveline Clutch (Torque Limiter) (Adjust And Run In)
 Tire and Air Pressure/Lug Nuts (Correct Torque)		Safety Decals (Installed)
 Wheel Bearings (Check, Grease, and Preload)		Operator’s Manual (Supplied)
ATTACHMENTS & INSTALLATION		Tractor PTO Shield (Installed)
 Deflectors Front And Rear		S.M.V. Emblem (Installed If Needed)
		Tongue Jack (Installation and Operation)
 Shredding Attachments
		Safety Tow Chain (Installed)
 Correct Blade Rotation Direction
		ADMA Driveline Safety Manual Supplied
 Axle Arms And Beams
		AEM Mower Safety Manual (Supplied in Canister)
 Tongue And Control Rods (Installed And Adjusted)
		AEM Mower Safety Video has been shown to Purchaser
 All Bolts - Pins And Nuts (Proper Torque)