Manuals / Alliance Laundry Systems / Cell Phone / Cell Phone

Alliance Laundry Systems CI 1650/325, CI 2050/325 Failure and information signals

Models: CI 1650/325

1 65

Download 65 pages 49.37 Kb

Page 28

Image 28

Failure and information signals

WARNING

If the procedure described here does not rectify the operational failure, the technical personnel of the laundry should be called in.

Activate hand protection

The foot pedal is pressed

There is a failure in the gas control (with a gas-heated ironer)

There is a failure in the relays for the heating elements

Important

When this signal is coming, press the reset button in case of a gas-heated ironer (see drawing p. 15). If this problem continues, an engineer must be consulted.

Page 28

Image 28

Alliance Laundry Systems CI 1650/325, CI 2050/325 instruction manual Failure and information signals

Contents

CI 1650/325 CI 2050/325 Cylinder ironerInstruction manual Page Contents ContentsSafety Information Initial setup of the machine Explanation of Safety Messages Safety InformationDANGER Turn off and lock out/tag out all electric power before opening Use care when handling recently processed or dried goodsElectric hazard inside Can cause death or serious injury Moving parts hazard. Can cause serious injurySafety notice CAUTION Note for installationVent exhaust outdoors and regularly clean lint away from machine Turn off and lock out/tag out all power until repairedImportant Safety Instructions Save These InstructionsPage Product description Intended useDescription of structural components side view Workplaces and noise leveltop view Technical data CI1650/325, CI2050/325 DimensionsNet weight Use of powerSound level measurement Conversion tableWarranty and service instructions Initial setup of the machine WARNING / DANGERTransport and machine fastening Never move the machine on inclined or uneven surfacesSetting up the machine 30 cmExhaust system Diameter If Pchannel 300 Pa, we recommend to increase the pipe dimension Equivalent pipe length in m for selected single resistancesRight-angled corner 90 degrees smooth bend R/D = 90 degrees angular bend R/D = 2 three sections1,5mm² Gas tube installation Basic checks Ventilation of the roomAir filters Exhaust gasesOperation Operating devices and their positionStarting the machine After switching the power to the machine, the display will showAfter 2 seconds X.XXFunctions Set the iron temperatureSet the ironing speed PedalIroning Return button not with guiding ribbonsEnding Failure and information signals There is an overheat problem more than 190 detected There is an overheat problem more than 190 detectedThere is a short circuit in the temperature sensor There is a broken wire in the temperature sensorPage Page Machine function, adjustment and troubleshooting Description of machine functionsOperating the foot pedal option Advice Setting the temperatureSetting the speed Manual drive Adjustments of the machine Guiding ironing beltsTightening the drive chain Tightening the ironing belts 1 Tightening the feeding belts To move the pins forward screw B3 until desired 2 Adjusting the gap between input table and main rollTo move the pins backward unscrew B3. Tighten bolts B2 B2B1 HS B3 T Troubleshooting Adjust distance chain wheel and sensor to 1mmHigh impedance phase to phase or phase to ground short circuit Temperature sensor out of orderOVL.d Description of the control system General description of the control systemSpeed control Control of exhaust ventilatorStart/stop function Control panel and function keys Menu structure and how to enter +- + +5 sec Manual version2 sec Menu structure+- + + 5 secManu adjusting menu t C or t F default CXX Cool default 80C XXX Low default 130CCoin adjusting menu on t C default COff t C default C On t F default F+ + + + Add XX defaultC1M coin 1 Medium C1H coin 1 HighTechnical menu ++ +X X X Adr X.X defaultkp XXXX default gas 300 default elec kd XXXX default gas 1000 default elecki XXXX default gas 0.5 default elec Start PWM defaultTemperature of probe rEv Y/n default YES not adjustable with coinTemperature of probe Display menu Central panelSigma explorer X X XMaintenance Safety adviceMaintenance scheme Daily maintenanceWeekly maintenance Monthly maintenanceFilter gas mixture Check filter on dust. Clean if dirty This space has to be cleaned every month also gas-heated ironersIf this is seriously polluted, you can open the top and clean it Frame right sideSubplating dust accumulation Half-yearly maintenance Runners and axial bearing runnerFeeding belts Ironer belts DriveScrapers