Manuals
/
Alliance Laundry Systems
/
Cell Phone
/
Cell Phone
Alliance Laundry Systems
CI 2050/325, CI 1650/325 instruction manual
Models:
CI 1650/325
1
65
65
Download
65 pages
49.37 Kb
58
59
60
61
62
63
64
65
<
>
Troubleshooting
Install
Warranty
Dimension
Maintenance
There is a broken wire in the temperature sensor
Initial setup of the machine
t C or t F default C
Failure and information signals
Adjustments of the machine
Page 65
Image 65
Page 64
Page 65
Image 65
Page 64
Contents
Instruction manual
Cylinder ironer
CI 1650/325 CI 2050/325
Page
Contents
Contents
Safety Information
Initial setup of the machine
DANGER
Safety Information
Explanation of Safety Messages
Use care when handling recently processed or dried goods
Turn off and lock out/tag out all electric power before opening
Electric hazard inside Can cause death or serious injury
Moving parts hazard. Can cause serious injury
CAUTION Note for installation
Safety notice
Vent exhaust outdoors and regularly clean lint away from machine
Turn off and lock out/tag out all power until repaired
Save These Instructions
Important Safety Instructions
Page
Intended use
Product description
Description of structural components
top view
Workplaces and noise level
side view
Dimensions
Technical data CI1650/325, CI2050/325
Net weight
Use of power
Conversion table
Sound level measurement
Warranty and service instructions
WARNING / DANGER
Initial setup of the machine
Transport and machine fastening
Never move the machine on inclined or uneven surfaces
30 cm
Setting up the machine
Exhaust system
Diameter
Equivalent pipe length in m for selected single resistances
If Pchannel 300 Pa, we recommend to increase the pipe dimension
Right-angled corner 90 degrees smooth bend R/D = 2
90 degrees angular bend R/D = 2 three sections
1,5mm²
Gas tube installation
Ventilation of the room
Basic checks
Exhaust gases
Air filters
Operating devices and their position
Operation
After switching the power to the machine, the display will show
Starting the machine
After 2 seconds
X.XX
Set the iron temperature
Functions
Set the ironing speed
Pedal
Ending
Return button not with guiding ribbons
Ironing
Failure and information signals
There is a short circuit in the temperature sensor
There is an overheat problem more than 190 detected
There is a broken wire in the temperature sensor
There is an overheat problem more than 190 detected
Page
Page
Description of machine functions
Machine function, adjustment and troubleshooting
Operating the foot pedal option
Setting the temperature
Advice
Setting the speed
Manual drive
Guiding ironing belts
Adjustments of the machine
Tightening the drive chain
Tightening the ironing belts
1 Tightening the feeding belts
To move the pins backward unscrew B3. Tighten bolts B2 B2B1 HS B3 T
2 Adjusting the gap between input table and main roll
To move the pins forward screw B3 until desired
Adjust distance chain wheel and sensor to 1mm
Troubleshooting
Temperature sensor out of order
High impedance phase to phase or phase to ground short circuit
OVL.d
General description of the control system
Description of the control system
Start/stop function
Control of exhaust ventilator
Speed control
Control panel and function keys
+- + +
Menu structure and how to enter
5 sec
Manual version
Menu structure
2 sec
+- + +
5 sec
t C or t F default C
Manu adjusting menu
XX Cool default 80C
XXX Low default 130C
on t C default C
Coin adjusting menu
Off t C default C
On t F default F
Add XX default
+ + + +
C1M coin 1 Medium
C1H coin 1 High
++ +
Technical menu
X X X
Adr X.X default
kd XXXX default gas 1000 default elec
kp XXXX default gas 300 default elec
ki XXXX default gas 0.5 default elec
Start PWM default
Temperature of probe
rEv Y/n default YES not adjustable with coin
Temperature of probe
Central panel
Display menu
Sigma explorer
X X X
Safety advice
Maintenance
Maintenance scheme
Daily maintenance
Monthly maintenance
Weekly maintenance
This space has to be cleaned every month also gas-heated ironers
Filter gas mixture Check filter on dust. Clean if dirty
If this is seriously polluted, you can open the top and clean it
Frame right side
Subplating dust accumulation
Runners and axial bearing runner
Half-yearly maintenance
Feeding belts
Drive
Ironer belts
Scrapers