Manuals / Alliance Laundry Systems / Cell Phone / Cell Phone

Alliance Laundry Systems CI 1650/325 Safety advice, Maintenance scheme, Daily maintenance

Models: CI 1650/325

1 65

Download 65 pages 49.37 Kb

Page 56

Maintenance

7

Maintenance

Safety advice

When starting the maintenance work on the ironer, the following should be observed:

1.Turn off the gas tap in case of a gas-heating ironer.

2.Ensure that the ironer has cooled down until it has reached the environmental temperature.

3.Use proper tools in order to avoid damage to the machine, which can result in personal injury.

Maintenance scheme

The cleaning and maintenance intervals mentioned below are based on a use of 8 hours a day and 5 days a week. If the use of this machine differs, the intervals given below can be adjusted linearly.

Daily maintenance

Cleaning:

Surrounding area

Daily clean the surrounding area of the machine. Keep it free from dust as much as possible. A clean workroom will prolong the life of the machine as less dust and dirt will be drawn in the machine.

Filter for gas-heated ironer

Gas-heated ironers are equipped with an air filter. This filter is located in the right-hand door of the machine. Clean it manually or with a vacuum cleaner after the machine has been turned off.

WARNING

Maintenance on the machine is solely reserved for the maintenance personnel.

56

Image 56

Alliance Laundry Systems CI 1650/325, CI 2050/325 Safety advice, Maintenance scheme, Daily maintenance

Contents

Instruction manual Cylinder ironerCI 1650/325 CI 2050/325 Page Contents ContentsSafety Information Initial setup of the machine DANGER Safety InformationExplanation of Safety Messages Turn off and lock out/tag out all electric power before opening Use care when handling recently processed or dried goodsElectric hazard inside Can cause death or serious injury Moving parts hazard. Can cause serious injurySafety notice CAUTION Note for installationVent exhaust outdoors and regularly clean lint away from machine Turn off and lock out/tag out all power until repairedImportant Safety Instructions Save These InstructionsPage Product description Intended useDescription of structural components top view Workplaces and noise levelside view Technical data CI1650/325, CI2050/325 DimensionsNet weight Use of powerSound level measurement Conversion tableWarranty and service instructions Initial setup of the machine WARNING / DANGERTransport and machine fastening Never move the machine on inclined or uneven surfacesSetting up the machine 30 cmExhaust system Diameter If Pchannel 300 Pa, we recommend to increase the pipe dimension Equivalent pipe length in m for selected single resistancesRight-angled corner 90 degrees smooth bend R/D = 90 degrees angular bend R/D = 2 three sections1,5mm² Gas tube installation Basic checks Ventilation of the roomAir filters Exhaust gasesOperation Operating devices and their positionStarting the machine After switching the power to the machine, the display will showAfter 2 seconds X.XXFunctions Set the iron temperatureSet the ironing speed PedalEnding Return button not with guiding ribbonsIroning Failure and information signals There is an overheat problem more than 190 detected There is an overheat problem more than 190 detectedThere is a short circuit in the temperature sensor There is a broken wire in the temperature sensorPage Page Machine function, adjustment and troubleshooting Description of machine functionsOperating the foot pedal option Advice Setting the temperatureSetting the speed Manual drive Adjustments of the machine Guiding ironing beltsTightening the drive chain Tightening the ironing belts 1 Tightening the feeding belts To move the pins backward unscrew B3. Tighten bolts B2 B2B1 HS B3 T 2 Adjusting the gap between input table and main rollTo move the pins forward screw B3 until desired Troubleshooting Adjust distance chain wheel and sensor to 1mmHigh impedance phase to phase or phase to ground short circuit Temperature sensor out of orderOVL.d Description of the control system General description of the control systemStart/stop function Control of exhaust ventilatorSpeed control Control panel and function keys Menu structure and how to enter +- + +5 sec Manual version2 sec Menu structure+- + + 5 secManu adjusting menu t C or t F default CXX Cool default 80C XXX Low default 130CCoin adjusting menu on t C default COff t C default C On t F default F+ + + + Add XX defaultC1M coin 1 Medium C1H coin 1 HighTechnical menu ++ +X X X Adr X.X defaultkp XXXX default gas 300 default elec kd XXXX default gas 1000 default elecki XXXX default gas 0.5 default elec Start PWM defaultTemperature of probe rEv Y/n default YES not adjustable with coinTemperature of probe Display menu Central panelSigma explorer X X XMaintenance Safety adviceMaintenance scheme Daily maintenanceWeekly maintenance Monthly maintenanceFilter gas mixture Check filter on dust. Clean if dirty This space has to be cleaned every month also gas-heated ironersIf this is seriously polluted, you can open the top and clean it Frame right sideSubplating dust accumulation Half-yearly maintenance Runners and axial bearing runnerFeeding belts Ironer belts DriveScrapers