Manuals / Alliance Laundry Systems / Cell Phone / Cell Phone

Alliance Laundry Systems CI 2050/325, CI 1650/325 X X X, kp XXXX default gas 300 default elec

Models: CI 1650/325

1 65

Download 65 pages 49.37 Kb

Page 53

kp XXXX [default: gas 300] [default: elec 400]

6

+

X X X X

-

+

X X X X

-

+

X X . X

-

+

X X

-

+

X X

-

+

X X

-

+

Remark:

kp XXXX [default: gas 300] [default: elec 400]

Value of the proportion of the P.I.D. regulator for the burner. Press the return button to choose this option.

kd XXXX [default: gas 1000] [default: elec 3000]

Differential value of the P.I.D. regulator for the burner. Press the return button to choose this option.

ki XXXX [default: gas 0.5] [default: elec 2.0]

Integrator value of the P.I.D. regulator for the burner. Press the return button to choose this option.

Start PWM [default: 40]

At the moment of ignition of the burner: as long as there is no feedback measured, this value will be sent (only with gas heating).

Minimum PWM (default: 25)

When the measured signal is smaller, this value will be sent (only with gas heating).

PWM XX

Test signal to check the PWM of the burner. The chosen value (25%, 50% or 100%) will be sent during normal operation, independently of the temperature. After a voltage interruption, PWM will automatically be put on "none" (only with gas heating).

L.r or Lr.SS [default: L.r]

This parameter affects the function of the frequency converter and must therefore never be changed, unless another type of converter is built in. Press the return button to choose this option.

Settings kp, kd, ki, SPW, MPW and PWM are not possible when heat = steam.

53

Image 53

Alliance Laundry Systems CI 2050/325 X X X, kp XXXX default gas 300 default elec, kd XXXX default gas 1000 default elec

Contents

Instruction manual Cylinder ironerCI 1650/325 CI 2050/325 Page Contents ContentsSafety Information Initial setup of the machine DANGER Safety InformationExplanation of Safety Messages Use care when handling recently processed or dried goods Turn off and lock out/tag out all electric power before openingElectric hazard inside Can cause death or serious injury Moving parts hazard. Can cause serious injuryCAUTION Note for installation Safety noticeVent exhaust outdoors and regularly clean lint away from machine Turn off and lock out/tag out all power until repairedSave These Instructions Important Safety InstructionsPage Intended use Product descriptionDescription of structural components top view Workplaces and noise levelside view Dimensions Technical data CI1650/325, CI2050/325Net weight Use of powerConversion table Sound level measurementWarranty and service instructions WARNING / DANGER Initial setup of the machineTransport and machine fastening Never move the machine on inclined or uneven surfaces30 cm Setting up the machineExhaust system Diameter Equivalent pipe length in m for selected single resistances If Pchannel 300 Pa, we recommend to increase the pipe dimensionRight-angled corner 90 degrees smooth bend R/D = 2 90 degrees angular bend R/D = 2 three sections1,5mm² Gas tube installation Ventilation of the room Basic checksExhaust gases Air filtersOperating devices and their position OperationAfter switching the power to the machine, the display will show Starting the machineAfter 2 seconds X.XXSet the iron temperature FunctionsSet the ironing speed PedalEnding Return button not with guiding ribbonsIroning Failure and information signals There is a short circuit in the temperature sensor There is an overheat problem more than 190 detectedThere is a broken wire in the temperature sensor There is an overheat problem more than 190 detectedPage Page Description of machine functions Machine function, adjustment and troubleshootingOperating the foot pedal option Setting the temperature AdviceSetting the speed Manual drive Guiding ironing belts Adjustments of the machineTightening the drive chain Tightening the ironing belts 1 Tightening the feeding belts To move the pins backward unscrew B3. Tighten bolts B2 B2B1 HS B3 T 2 Adjusting the gap between input table and main rollTo move the pins forward screw B3 until desired Adjust distance chain wheel and sensor to 1mm TroubleshootingTemperature sensor out of order High impedance phase to phase or phase to ground short circuitOVL.d General description of the control system Description of the control systemStart/stop function Control of exhaust ventilatorSpeed control Control panel and function keys +- + + Menu structure and how to enter5 sec Manual versionMenu structure 2 sec+- + + 5 sect C or t F default C Manu adjusting menuXX Cool default 80C XXX Low default 130Con t C default C Coin adjusting menuOff t C default C On t F default FAdd XX default + + + +C1M coin 1 Medium C1H coin 1 High++ + Technical menuX X X Adr X.X defaultkd XXXX default gas 1000 default elec kp XXXX default gas 300 default elecki XXXX default gas 0.5 default elec Start PWM defaultTemperature of probe rEv Y/n default YES not adjustable with coinTemperature of probe Central panel Display menuSigma explorer X X XSafety advice MaintenanceMaintenance scheme Daily maintenanceMonthly maintenance Weekly maintenanceThis space has to be cleaned every month also gas-heated ironers Filter gas mixture Check filter on dust. Clean if dirtyIf this is seriously polluted, you can open the top and clean it Frame right sideSubplating dust accumulation Runners and axial bearing runner Half-yearly maintenanceFeeding belts Drive Ironer beltsScrapers