Manuals / Alliance Laundry Systems / Cell Phone / Cell Phone

Alliance Laundry Systems CI 2050/325, CI 1650/325 Initial setup of the machine, Warning / Danger

Models: CI 1650/325

1 65

Download 65 pages 49.37 Kb

Page 15

Initial setup of the machine

3

Initial setup of the machine

Transport and machine fastening

The machine has been secured with bolts on a solid wooden frame and has been safely packed in plastic sheeting from the factory.

WARNING / DANGER

During all transport and handling of the machine, there is a risk of the machine tipping over or falling over onto persons. In order to avoid accidents, the following should therefore be observed:

During transport and handling with a fork-lift truck, the forks should be situated proportional to the center of gravity as shown below and on the packing of the machine.

Never use lifting and hoisting material with a too small lifting capacity. See paragraph 'Technical data' concerning the weight of the machine.

The max. weight of the machine including packing is stated on the packing of the machine.

Never move the machine on inclined or uneven surfaces.

Important

We recommend to let the wooden frame remain bolted for the use of transport with fork-lift truck, until the machine is near the place of setting up.

15

Image 15

Alliance Laundry Systems CI 2050/325 Initial setup of the machine, Warning / Danger, Transport and machine fastening

Contents

Cylinder ironer CI 1650/325 CI 2050/325Instruction manual Page Initial setup of the machine ContentsContents Safety Information Safety Information Explanation of Safety MessagesDANGER Moving parts hazard. Can cause serious injury Turn off and lock out/tag out all electric power before openingUse care when handling recently processed or dried goods Electric hazard inside Can cause death or serious injuryTurn off and lock out/tag out all power until repaired Safety noticeCAUTION Note for installation Vent exhaust outdoors and regularly clean lint away from machineSave These Instructions Important Safety InstructionsPage Intended use Product descriptionDescription of structural components Workplaces and noise level side viewtop view Use of power Technical data CI1650/325, CI2050/325Dimensions Net weightConversion table Sound level measurementWarranty and service instructions Never move the machine on inclined or uneven surfaces Initial setup of the machineWARNING / DANGER Transport and machine fastening30 cm Setting up the machineExhaust system Diameter 90 degrees angular bend R/D = 2 three sections If Pchannel 300 Pa, we recommend to increase the pipe dimensionEquivalent pipe length in m for selected single resistances Right-angled corner 90 degrees smooth bend R/D = 21,5mm² Gas tube installation Ventilation of the room Basic checksExhaust gases Air filtersOperating devices and their position OperationX.XX Starting the machineAfter switching the power to the machine, the display will show After 2 secondsPedal FunctionsSet the iron temperature Set the ironing speedReturn button not with guiding ribbons IroningEnding Failure and information signals There is an overheat problem more than 190 detected There is an overheat problem more than 190 detectedThere is a short circuit in the temperature sensor There is a broken wire in the temperature sensorPage Page Description of machine functions Machine function, adjustment and troubleshootingOperating the foot pedal option Setting the temperature AdviceSetting the speed Manual drive Guiding ironing belts Adjustments of the machineTightening the drive chain Tightening the ironing belts 1 Tightening the feeding belts 2 Adjusting the gap between input table and main roll To move the pins forward screw B3 until desiredTo move the pins backward unscrew B3. Tighten bolts B2 B2B1 HS B3 T High impedance phase to phase or phase to ground short circuit TroubleshootingAdjust distance chain wheel and sensor to 1mm Temperature sensor out of orderOVL.d General description of the control system Description of the control systemControl of exhaust ventilator Speed controlStart/stop function Control panel and function keys Manual version Menu structure and how to enter+- + + 5 sec5 sec 2 secMenu structure +- + +XXX Low default 130C Manu adjusting menut C or t F default C XX Cool default 80COn t F default F Coin adjusting menuon t C default C Off t C default CC1H coin 1 High + + + +Add XX default C1M coin 1 MediumAdr X.X default Technical menu++ + X X XStart PWM default kp XXXX default gas 300 default eleckd XXXX default gas 1000 default elec ki XXXX default gas 0.5 default elecrEv Y/n default YES not adjustable with coin Temperature of probeTemperature of probe X X X Display menuCentral panel Sigma explorerDaily maintenance MaintenanceSafety advice Maintenance schemeMonthly maintenance Weekly maintenanceFrame right side Filter gas mixture Check filter on dust. Clean if dirtyThis space has to be cleaned every month also gas-heated ironers If this is seriously polluted, you can open the top and clean itSubplating dust accumulation Runners and axial bearing runner Half-yearly maintenanceFeeding belts Drive Ironer beltsScrapers