To Replace DSI Module | American Dryer Corp AD-170 manual

To Replace DSI Module

1.Discontinue power to the dryer.

2.Remove the wires connected to the terminal

strip at the bottom of the module.

3. Remove the four (4) screws securing the module to the mounting bracket.

4. Replace module by reversing procedure.

5. Reestablish power to dryer.

C. Thermostats

To Replace Burner Hi-Limit Thermostat (Gas Models Only)

This thermostat is an important safety device serving as an added protection against failure of the air flow (sail switch) to open in the event of motor failure or reduced airflow condition.

IMPORTANT: Under no circumstances should heat circuit safety devices ever be disabled.

1. Discontinue power to dryer.

2. Disconnect wires from hi-limit thermostat.

3. Remove screw, washer, and nut securing thermostat to the bracket. Remove thermostat.

4. Reverse procedure for installing new thermostat.

5. Reestablish power to dryer.

21

Image 25

American Dryer Corp AD-170 service manual To Replace DSI Module

Contents

AD-170 AD-170 Retain This Manual In a Safe Place For Future ReferencePage For Your Safety Table of Contents Sail Switch Assembly Important Information Safety Precautions Cleaning Routine Maintenance Lubrication Adjustments Enclosure, Air Supply, and Exhaust Requirements Installation Requirements Electrical and Gas Requirements Operational Service Check Procedure Description of Parts Computer Panel AssemblyControl Box DSI Module Gas Models Only Drive Motor Gas Burner AssemblyBlower Motor and Impellor Hz Gas Models Only Blower Motor and Impellor 50Hz, 60Hz Steam & 50Hz Gas Tumbler Bearing and Pulley Arrangement Idler AssemblyBasket Tumbler Sail Switch Gas Models only Main Door SwitchHi-Limit Gas Models Only Lint Drawer Switch Automatic Reset ThermostatLint Drawer Steam Damper System Introduction Servicing Computer Controls To Replace Computer To Replace Keyboard Label Assembly To Replace Microprocessor Temperature Sensor Probe Page To Replace Main Burner Orifices To Replace Gas Valve see burner illustration on To Test and Adjust Gas Water Column Pressure To Convert from Natural Gas to L.P. Gas To Replace Burner Tubes To Replace DSI Module Sail Switch Assembly Gas Models Only To Adjust Sail Switch To Replace Sail Switch To Install New Main Door Glass To Replace Main Door Assembly To Replace Main Door Hinge Pad To Replace Front Panel To Replace Small Idler Pulley Pulleys To Replace Tumbler Pulley To Replace Motor Pulley To Replace Large Idler PulleyPage To Replace Tumbler Basket or Tumbler Basket Support Basket Alignment Lateral Side to Side Adjustment Important Never strike the shaft directly with a hammer To Replace Front Idler Shaft Pillow Block Bearing To Replace Front Basket Support Pillow Block Bearing To Replace Rear Idler Shaft Pillow Block Bearing Belt Tension Adjustment Basket to IdlerBelts See illustrations in section F Pulleys To Replace V-Belts Belt Tension Adjustment Motor to IdlerMotors To Replace Drive Motor Page To Replace Lint Drawer Switch Lint Drawer Assembly To Replace Lint ScreenImpellor No display on computer TroubleshootingComputer will not accept key pad entries Drive motor runs, burner is on, but basket will not turn Dryer will not start, but computer display indicators are on Dryer operates but is taking too long to dry Dryer operates, probe sparks, but gas does not flow Thermal overload for drive motor is tripping Dryer is cycling on burner hi-limit safety thermostatOverload for impellor fan motor is tripping Dryer does not start. Display reads door Display reads dSFL. Dryer Sensor Circuit FailureThere is excessive vibration coming from the basket Electrical Trouble Shooting Diagnostic LED Display Failure Codes Phase 5 OPL System Diagnostics LED Display Indicators Page Page Cycle Status LED Display/Codes CY F LED Display Codes Fill Computer Logic and Wiring Diagram Fault CodesPage No Display Condition Page Blower motor does not operate, drive motor runs Door condition Microprocessor reads Dsfl Motor Plate High and Low Voltage Technical Information Information on the Data Label Data Label Contacting American Dryer Corporation ADC HOW to USE a Manometer Using a Manometer AD-170SE Tool List ADC450400 1- 02/27/98-50