Setting the Menus (Cont.)
FIRST TIME SET UP
Setting the present time, date and | <FIRST TIME SET UP> |
|
Daylight Saving Time settings (TIME | TIME DATE ADJUST | STOP |
DATE ADJUST) | TAPE END | |
QUASI | ON | |
page 28 | VIDEO MODE | AUTO |
TAPE LENGTH | ||
| BUZZER | WRNG |
|
|
Setting operation of VCR when the tape reaches its end during recording or playback (TAPE END)
The VCR’s function when the tape reaches its end during recording is as follows.
STOP : The tape stops, the indication “End” appears on the fluorescent display and “TAPE END” on screen. When CALL OUT is set to WRNG•TAPE END, a call signal is output from
WRNG•REMAIN : The buzzer sounds when there is any malfunction in the VCR or the tape has approximately 9 minutes (at 6H mode) left.
OFF | : The buzzer does not sound. |
Note
•To stop the buzzer:
Press MENU button once. If <MAIN MENU> appears, press MENU button again to exit the menu. When the VCR is locked, press LOCK button to unlock the VCR, then the buzzer stops.
Setting the
See the next section.
RS-232C
the CALL OUT terminal.
REWIND : Rewinds the tape to the beginning and stops (except during timer recording). When CALL OUT is set to WRNG•TAPE END and a tape reaches its end, a call signal is output for 2 seconds from the CALL OUT terminal.
REPEAT : Rewinds the tape to the beginning and resumes the recording. When CALL OUT is set to
Setting the transmission rate
(TRANSMISSION RATE)
When JOG is turned, the display will be switched in the order of 1200 (bps) 
2400 
4800 
9600 
1200 
...
Setting the data bit length (DATA
1200 | |
TRANSMISSION RATE | |
DATA BIT LENGTH | 8BIT |
STOP BIT LENGTH | 1BIT |
PARITY BIT | NONE |
DELIMITER<SEND> | CR•LF |
DELIMITER<RECEIVE> | CR |
VCR ADDRESS | NONE |
WRNG•TAPE END and a tape reaches its end, a call signal is output for 2 seconds from the CALL OUT terminal.
ALARM•PROT (alarm protection) :
If any alarm recordings are present on the tape and the tape stops, the indication “End” appears on the fluorescent display and “TAPE END” on screen. When CALL OUT is set to WRNG•TAPE END, a call signal is output from the CALL OUT terminal. If there is no alarm recording, the VCR rewinds the tape to the beginning and resumes the recording.
Go to page 8 for the VCR’s function when the tape reaches its end during playback.
Setting Quasi-V-sync on or off (QUASI V-SYNC)
ON :
signal in the special effects playback (
page 16) or normal playback in
OFF :
Note
•Some multiplexers may require QUASI
Setting the playback/recording color mode (VIDEO MODE)
AUTO
B/W
Setting the tape length (TAPE LENGTH)
Setting to sound buzzer during warning (BUZZER)
WRNG
WRNG•TAPE END : The buzzer sounds when there is any malfunction in the VCR or the tape reaches its end.
BIT LENGTH)
When JOG is turned, the display will be switched in the order of
8BIT 
7BIT 
8BIT 
...
Setting the stop bit length (STOP BIT LENGTH)
When JOG is turned, the display will be switched in the order of
1BIT 
2BIT 
1BIT 
...
Setting the parity bit (PARITY BIT)
When JOG is turned, the display will be switched in the order of
NONE 
ODD 
EVEN 
NONE 
...
Setting a character marking the end of a status or error code (DELIMITER<SEND>)
When JOG is turned, the display will be switched in the order of
CR•LF 
CR 
CR•LF 
...
Setting a character marking the end of a command (DELIMITER<RECEIVE>)
When JOG is turned, the display will be switched in the order of
CR•LF 
CR 
CR•LF 
...
Setting the ID number of the VCR (VCR ADDRESS)
When JOG is turned, the display will be switched in the order of NONE 
VCR01 
VCR02 
..... 
VCR254 
VCR255.
32 Installation
Note A point to notice | Info. Supplementary information |
