Series Recording Connection | American Dynamics ADV096HD instruction

Series Recording Connection

Connect VCRs to be used as shown below.( page 12 for the menu setting)

ALM RST REC GND ALM MODE	CLK CALL
IN	OUT

1st VCR

	*1
ALM RST REC GND ALM MODE	CLK CALL
IN	OUT

2nd VCR

*1 : This connection is necessary in case of Series Recording 2.

Remote Recording Connection

Connect the VCR with a remote switch as to the right. ( terminal)

page 13 for the menu setting and page 36 for the rating of each

ALM RST REC GND ALM MODE	CLK CALL
IN	OUT

Remote switch

Synchronous Recording Connection

Connect VCRs as shown below. ( page 14 for the menu setting)

Note The number of VCRs to be connected varies by the recording time mode selected.

Camera 1
	1st VCR
	VIDEO IN
Camera 2	Switcher
	2nd VCR
	VIDEO IN
Camera 3	3rd VCR
	VIDEO IN

CLK OUT

REC IN

CLK OUT

REC IN

Connection for External Time Clock Adjustment

Connect VCRs as shown below. ( next page for the menu setting and page 36 for the rating of each terminal)

Switch

*1

ALM RST REC GND ALM MODE	CLK CALL
IN	OUT

1st VCR

ALM RST REC GND ALM MODE	CLK CALL
IN	OUT

2nd VCR

*1 : When connecting the MODE OUT terminal of the first VCR with the RST IN terminal of the second VCR, the on-screen clock of the second VCR can be adjusted to that of the first VCR.

Reference page

Installation 27

Image 31

American Dynamics ADV096HD Series Recording Connection, Remote Recording Connection, Synchronous Recording Connection

Contents

Super VHS ET Expansion Technology ADV096HD Avertissement Important Safeguards Iii Important SafeguardsInformation Introduction Contents Features Controls and Functions Controls and Functions REC Mode OUTALM RST Basic Functions Loading/Unloading a Tape Recording Check Function Manual RecordingRecording/playback time Audio recording/playback Fast forwarding a tape 32 for Tape END settingPlayback Rewinding a tape When adjusting the clock to the exact second Adjusting the ClockJOG dial Shuttle ring Advanced Functions Recording TechniquesProgram to Record menu appears Alarm Recording Holiday set upSpecial day of the week Series Recording Display during alarm recordingRecording Techniques Emergency Recording One shot/Interval Recording When the tape reaches its end during recordingRemote Recording Repeat Recording Number of cameras Recording time modeSynchronous Recording VCR After a power failure Additional FeaturesMemory backup in case of power failure Displaying/clearing the alarm list Special Effects Playback Additional Features Vertical adjustment picture vibration at the top and bottom Adjustment during PlaybackTracking adjustment Picture quality adjustment Skip search Searching TechniquesCounter memory stop Index search Time Date Search menu appears Time date search RS-232C setting Configuring the time lapse VCRConnecting to a Personal Computer Status Response codes from the VCR to outside Commands from personal computerCommand Commands set to the VCR Status Response codes from the VCR Commands and Responses Using with Personal Computer 100=MAIN Menu =STOP, 1=REWIND, 2=REPEAT =SERIES, 1=REC-START/STOP =SYNC REC Error code Connections for Various Functions InstallationConnecting with Cctv camera, monitor and sensor Alarm Recording Connection Synchronous Recording Connection Connection for External Time Clock AdjustmentSeries Recording Connection Remote Recording Connection Setting the current time to exact second Setting the ClockExternal time clock adjustment Menu Chart Setting the MenusSet the menus by the following steps Press Menu button Setting the Menus Shotinterval Power Loss ListPower Shotfield RS-232C SymptomRemedy Before Calling for ServiceOthers Playback Lack of video signal input Self-diagnostic functionMonitor Cause Remedy To turn off the indicator When the tape ends ALM/MODE/CALL OUT terminals screw Control Input/Output Signals and CircuitCLK OUT signal ALM/RST/REC in terminals screw General SpecificationsPage Page 872C276B9 8200-0206-02