Manuals / American Power Conversion / Household Appliance / Air Conditioner

American Power Conversion FM, DX manual Final Inspection Checklist, Ensure that, Owner Acceptance

Models: DX FM

1 96

Download 96 pages 14.45 Kb

Page 25

Final Inspection Checklist

Final Inspection Checklist

Ensure that:

The system interior and exterior are clean and free from debris.

Installed options (smoke detectors, firestat, water detector, remote sensor, remote relay shutdown, dry contact alarm, essential/non-essential lockout, Redundant Unit Group control, condensate pump, etc.) are operating correctly.

Setpoints and deadbands are set.

Packaging materials are disposed of properly.

You have sent the start-up form to APC.

Owner Acceptance

To ensure proper unit operation and trouble free operation the following procedures must be completed and filed with the customer for future reference.

•Review installation of the equipment. Verify that installation is in compliance with Installation manual instructions/recommendations.

•Complete start-up checklist and file with owner and factory to activate warranty policy.

•Train personnel responsible for maintenance and minor adjustments to temperature & humidity set points.

•Recommend spare parts for the owner to keep on hand, especially for critical operation installations.

•Offer a list of contacts for service, technical assistance, replacement parts.

NetworkAIR FM DX 60 Hz Operation, Maintenance, and Troubleshooting

15

Image 25

American Power Conversion FM, DX manual Final Inspection Checklist, Ensure that, Owner Acceptance

Contents

Operation, Maintenance, and Troubleshooting 60 HzNetworkAIR FM DX Precision Air Conditioner Page American Power Conversion Legal Disclaimer Page General Information SafetyOperation ContentsMechanical and Refrigeration Inspection Checklist Temperature alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Humidity alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Maintenance intervals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Alarm delay Network Management Card MaintenanceWarranty TroubleshootingPage Modules, Systems, and Groups General InformationModule SystemGroup Symbols Used in this Manual SafetySafety symbols that may be used in this manual Cross-referencesymbols used in this manualLockout/tagout Safety HazardsElectrical hazards Static dischargeDisplay Interface OperationFunction Scrolling status screens Using the Display InterfaceStatus Screen Name Status Information DisplayedMain menu screen Password entryNavigating the interface Factory default settings Change settingsStart the System Stop the SystemCommissioning Power on Power On/Off ProcedurePower off Initial Inspection Checklist Commissioning ChecklistsMechanical and Refrigeration Inspection Checklist Electrical Inspection ChecklistEnsure that Ensure thatUser Interface Box Inspection Checklist Mechanical Inspection Air-cooledChecklistEnsure that Ensure thatWhile the equipment is operating, ensure that Start-upInspection ChecklistEnsure that Final Inspection ChecklistOwner Acceptance System options System ConfigurationPage Up Down System delays Building management Sensor setupApplicable Settings Settings for fluid-cooledoptionsFluid-CoilType Valve types Flow Switch Multi Cndsr Vlv 3-wayActuator types Coil Fluid 3-wayEconomizer isolation valve optional Econ Isolator Valve EnableEcon Isolator Close Dly Econ Isolator Open Dly Page Input contacts Contacts and RelaysDescription/Function Output relays Configure Module Module ConfigurationAlarm detectors Calibrate airflow manually Module ControlCalibrate airflow automatically Reset humidifier Reset Variable Frequency DriveSet up humidifier How the modes work Control the EnvironmentDX Dehumidify. Similar to DX cooling, the output for dehumidification is determined by the difference between the setpoint and the average return humidity from each of the Modules in the System if more than one Module is present. The deadband is used to engage both compressors incrementally with increasing demand. Each Module in the System is assigned an equal division of the deadband a percentage of relative humidity. Both compressors in a Module are engaged when the assigned division of the deadband above the setpoint is reached. If the average return humidity reaches the setpoint plus the entire deadband, all of the compressors will be engaged until the humidity drops below the setpoint plus the deadband. Unlike DX cooling, the compressors in each Module are normally set to work as a single unit instead of separately. The use of one or two compressors per Module is based on the Dehum. Capacity setting Path Main Menu Setup System # System Config System Options Setpoints Deadbands Two-ModuleSystem Cool Deadband Compressor AllocationTo set the dehumidify deadband for your System Essential functions ModesPID controls How to tune the PIDsControl PID Tuning CorrectionProportional IntegralTemperature alarms AlarmsHumidity alarms Maintenance intervalsAlarm delay Group configuration GroupMode Group settingsRange Share ifSystem failure events Password and time-out DisplayTemperature and pressure units Date and timeHow to update the firmware Adjust displayProduct data Reset to defaultsNetwork configuration Network ConfigurationScrolling status screens View Status ReadingsModule status Group status System statusPath Main Status System # Path: Main > Status > GroupView log View Event LogMajor or minor alarm LEDs Respond to AlarmsView active alarms Clear active alarmsDisplayed Alarm Message Alarm messages and suggested actionsAction Required Action Required Displayed Alarm MessageCondensate Pump Fail Env Temperature Low Displayed Alarm MessageAction Required Action Required Displayed Alarm MessageSystem Options Action Required Displayed Alarm MessageHumidifier System Config System Options Displayed Alarm MessageAction Required Comm Lost state, or OffAction Required Displayed Alarm MessageSupply Humidity High Action Required Displayed Alarm MessageSystem Comm Lost Network Management Card Quick ConfigurationTCP/IP configuration methods OverviewBOOTP and DHCP configuration APC Device IP Configuration WizardPath Setup System Network Config A Vendor Class Identifier APC by default Remote access to the control console 1.Choose Network from the Control Console menu Control consoleOverview Access a Configured UnitWeb interface Telnet/SSHFTP/SCP SNMPRecover From a Lost Password Monthly Preventive Maintenance MaintenanceCleanliness EnvironmentElectrical MechanicalMechanical Quarterly Preventive MaintenanceElectrical Verify the following modes of operation Functional testsFull cooling Full reheat Humidification Dehumidification MultiCool EconomizerCleanliness Semi-AnnualPreventive MaintenanceMechanical ElectricalMeasure the refrigerant pressures Functional testsProblem TroubleshootingPossible Cause Corrective ActionPossible Cause ProblemCorrective Action Compressor fails toPossible Cause ProblemCorrective Action Compressor noisyPossible Cause ProblemCorrective Action Head pressure tooPossible Cause ProblemCorrective Action Suction pressure tooPage One-YearFactory Warranty WarrantyTerms of warranty Non-transferablewarrantyWarranty claims Claims Warranty ProceduresParts Page Page APC Worldwide Customer Support 990-3127990-3127 10/2007