Manuals / American Power Conversion / Household Appliance / Air Conditioner

American Power Conversion FM, DX Control console, Choose Network from the Control Console menu

Models: DX FM

1 96

Download 96 pages 14.45 Kb

Page 75

Control console

After you log on at the control console, as described in “Remote access to the control console” on page 64:

1.Choose Network from the Control Console menu.

2.Choose TCP/IP from the Network menu.

3.If you are not using a BOOTP or DHCP server to configure the TCP/IP settings, select the Boot Mode menu. Select Manual boot mode, and then press ESC to return to the TCP/IP menu. (Changes will take effect when you log out.)

4.Set the System IP, Subnet Mask, and Default Gateway address values.

5.Press CTRL+C to exit to the Control Console menu.

6.Log out (option 4 in the Control Console menu)

NetworkAIR FM DX 60 Hz Operation, Maintenance, and Troubleshooting

65

Image 75

American Power Conversion FM, DX manual Control console, Choose Network from the Control Console menu

Contents

60 Hz Operation, Maintenance, and TroubleshootingNetworkAIR FM DX Precision Air Conditioner Page American Power Conversion Legal Disclaimer Page Contents SafetyGeneral Information OperationMechanical and Refrigeration Inspection Checklist Temperature alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Humidity alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Maintenance intervals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Alarm delay Network Management Card MaintenanceWarranty TroubleshootingPage System General InformationModules, Systems, and Groups ModuleGroup Cross-referencesymbols used in this manual SafetySymbols Used in this Manual Safety symbols that may be used in this manualStatic discharge Safety HazardsLockout/tagout Electrical hazardsOperation Display InterfaceFunction Status Information Displayed Using the Display InterfaceScrolling status screens Status Screen NamePassword entry Main menu screenNavigating the interface Stop the System Change settingsFactory default settings Start the SystemCommissioning Power On/Off Procedure Power onPower off Initial Inspection Checklist Commissioning ChecklistsEnsure that Electrical Inspection ChecklistMechanical and Refrigeration Inspection Checklist Ensure thatEnsure that Mechanical Inspection Air-cooledChecklistUser Interface Box Inspection Checklist Ensure thatWhile the equipment is operating, ensure that Start-upInspection ChecklistFinal Inspection Checklist Ensure thatOwner Acceptance System options System ConfigurationPage Up Down System delays Building management Sensor setupSettings for fluid-cooledoptions Applicable SettingsFluid-CoilType Coil Fluid 3-way Flow Switch Multi Cndsr Vlv 3-wayValve types Actuator typesEcon Isolator Valve Enable Economizer isolation valve optionalEcon Isolator Close Dly Econ Isolator Open Dly Page Input contacts Contacts and RelaysDescription/Function Output relays Module Configuration Configure ModuleAlarm detectors Module Control Calibrate airflow manuallyCalibrate airflow automatically Reset Variable Frequency Drive Reset humidifierSet up humidifier How the modes work Control the EnvironmentDX Dehumidify. Similar to DX cooling, the output for dehumidification is determined by the difference between the setpoint and the average return humidity from each of the Modules in the System if more than one Module is present. The deadband is used to engage both compressors incrementally with increasing demand. Each Module in the System is assigned an equal division of the deadband a percentage of relative humidity. Both compressors in a Module are engaged when the assigned division of the deadband above the setpoint is reached. If the average return humidity reaches the setpoint plus the entire deadband, all of the compressors will be engaged until the humidity drops below the setpoint plus the deadband. Unlike DX cooling, the compressors in each Module are normally set to work as a single unit instead of separately. The use of one or two compressors per Module is based on the Dehum. Capacity setting Path Main Menu Setup System # System Config System Options Setpoints Deadbands Two-ModuleSystem Cool Deadband Compressor AllocationTo set the dehumidify deadband for your System Essential functions ModesPID controls How to tune the PIDsIntegral PID Tuning CorrectionControl ProportionalMaintenance intervals AlarmsTemperature alarms Humidity alarmsAlarm delay Group configuration GroupShare if Group settingsMode RangeSystem failure events Date and time DisplayPassword and time-out Temperature and pressure unitsHow to update the firmware Adjust displayProduct data Reset to defaultsNetwork configuration Network ConfigurationView Status Readings Scrolling status screensModule status Path: Main > Status > Group System statusGroup status Path Main Status System #View log View Event LogClear active alarms Respond to AlarmsMajor or minor alarm LEDs View active alarmsAlarm messages and suggested actions Displayed Alarm MessageAction Required Displayed Alarm Message Action RequiredCondensate Pump Fail Displayed Alarm Message Env Temperature LowAction Required Displayed Alarm Message Action RequiredSystem Options Displayed Alarm Message Action RequiredHumidifier Comm Lost state, or Off Displayed Alarm MessageSystem Config System Options Action RequiredDisplayed Alarm Message Action RequiredSupply Humidity High Displayed Alarm Message Action RequiredSystem Comm Lost Overview Quick ConfigurationNetwork Management Card TCP/IP configuration methodsAPC Device IP Configuration Wizard BOOTP and DHCP configurationPath Setup System Network Config A Vendor Class Identifier APC by default Remote access to the control console 1.Choose Network from the Control Console menu Control consoleTelnet/SSH Access a Configured UnitOverview Web interfaceFTP/SCP SNMPRecover From a Lost Password Environment MaintenanceMonthly Preventive Maintenance CleanlinessElectrical MechanicalQuarterly Preventive Maintenance MechanicalElectrical Dehumidification MultiCool Economizer Functional testsVerify the following modes of operation Full cooling Full reheat HumidificationElectrical Semi-AnnualPreventive MaintenanceCleanliness MechanicalMeasure the refrigerant pressures Functional testsCorrective Action TroubleshootingProblem Possible CauseCompressor fails to ProblemPossible Cause Corrective ActionCompressor noisy ProblemPossible Cause Corrective ActionHead pressure too ProblemPossible Cause Corrective ActionSuction pressure too ProblemPossible Cause Corrective ActionPage Non-transferablewarranty WarrantyOne-YearFactory Warranty Terms of warrantyWarranty claims Warranty Procedures ClaimsParts Page Page 10/2007 990-3127APC Worldwide Customer Support 990-3127