Appendix B – Programmer’s Interface for System Diagnostics

Verbosity Settings

The verbosity (v) settings (v0, v1, v2, v3) correspond to the level of detail that will be displayed, with v0 being the lowest level of detail and v3 being the highest level. The v3 setting is not supported for the “all components” setting. The commands ~scr! or ~scri0v#! will access the lowest level of detail (verbosity) for all components. The command ~scri#v#! will display higher levels of detail depending on the values entered for the verbosity settings.

Note: The “all components” setting (0) will display the lowest level of detail no matter which verbosity setting is used.

Component Settings

Detailed information for a single system component can be specified by using its identity (i) number setting (i0 through i4 and i7) in the following table. The “all components” setting (i0) will display the lowest level of detail no matter which verbosity setting is used.

Component

Identity Number Setting

 

 

All Components

i0

Enclosure

i1

Storage Blocks

i2

Communication Interfaces

i3

Hardware & Boards

i4

System Sensors

i7

Tip: The information in the above table is displayed when you enter ~scr! or ~scri0v1!

General Rules for Octaire Diagnostic Commands

In a multi-enclosure system, the splash screen displays information only for the enclosure that is connected directly to the PC

If the verbosity setting is omitted, the verbosity level will be the lowest (v0)

The component setting must be included; otherwise, entering any of the verbosity settings alone will result in a display equivalent to i0v0

If both settings are omitted during a query (~scr!), the information displayed will be at the lowest verbosity level for all components (i0v0)

At system boot, the information for an scri1v0! command is displayed

To access the lowest level of verbosity for all components:

1.Enter ~scr! or ~scri0v#! (# = any verbosity setting)

To access a specific level of verbosity for a specific component:

2.Enter ~scri#v# where the first # is the component (identity) setting and the second # is the verbosity setting (either may be specified first).

All combinations are valid except for v3i0, which is not supported.

3.Enter ! (to send the command).

Example: ~scrv3i7! or ~scri7v3! (displays the highest level of detail for the system sensors).

98

Octaire Instruction Manual

Page 103
Image 103
AMX instruction manual Verbosity Settings, Component Settings, General Rules for Octaire Diagnostic Commands

Octaire specifications

The AMX Octaire is a remarkable aircraft designed to meet the evolving demands of modern aviation. Renowned for its combination of advanced technology, efficiency, and versatility, the Octaire stands out in the realm of business jets and regional transport.

One of the main features of the AMX Octaire is its sleek aerodynamic design, which not only enhances aesthetics but significantly contributes to fuel efficiency. The aircraft's fuselage is built using advanced composite materials, which reduce weight while maintaining structural integrity. This results in improved performance and operational costs, making the Octaire an attractive option for companies and individuals seeking economical flying solutions.

Powered by two state-of-the-art turbofan engines, the AMX Octaire is capable of reaching an impressive cruising speed while optimizing fuel consumption. These engines are equipped with next-generation noise reduction technologies that conform to stringent environmental regulations, minimizing the aircraft's carbon footprint and contributing to sustainable aviation practices.

The cockpit of the Octaire features cutting-edge avionics, including multifunction displays and an intuitive interface for pilots. This technology enhances situational awareness and simplifies navigation, allowing for a smoother flight experience. The integration of fly-by-wire controls ensures precision handling and improved safety, making the Octaire a reliable choice for both seasoned pilots and newcomers.

Passenger comfort is a top priority in the design of the AMX Octaire. The cabin is spacious and customizable, featuring luxurious seating arrangements, modern entertainment systems, and advanced climate control. High-capacity windows provide ample natural light, creating an inviting atmosphere that enhances the onboard experience. With soundproofing materials expertly incorporated into the design, passengers can enjoy a serene environment during their journeys.

Versatility is another hallmark of the AMX Octaire. It can be adapted for various roles, including business travel, medevac missions, and cargo transport. This flexibility ensures that the Octaire can meet the needs of a diverse clientele, from corporate executives to humanitarian organizations.

In summary, the AMX Octaire is a sophisticated aircraft that embodies efficiency, comfort, and technological advancement. Its design and features position it as a leader in the aviation market, promising to deliver exceptional performance for years to come. Whether used for business or specialized operations, the Octaire is poised to redefine expectations in air travel.