Installation & Setup

Installation & Setup

Site Recommendations

When placing the enclosure, follow the recommendations and precautions in this section to reduce potential installation and operation hazards. For general specifications, see page 13; for individual signal specifications, see the “Signal Types & Specifications” chapter (page 39).

Environment

Choose a clean, dust free, (preferably) air-conditioned location.

Avoid areas with direct sunlight, heat sources, or high levels of EMI (Electromagnetic

Interference).

Chassis Accessibility

Make sure the front and rear panels of the enclosure are accessible, so that you can monitor the LED indicators. Leaving adequate clearance at the rear will also allow for easier cabling and service.

Power

The source’s electrical outlet should be installed near the router, easily accessible, and properly grounded. Power should come from a building branch circuit. We recommend that a second, independent branch be used for the second AC inlet feed to the enclosure (see page 27). Use a minimum breaker current rating of 30 A for 110 V or 15 A for 230 V.

To avoid an overload, note the power consumption rating of all the equipment connected to the circuit breaker before applying power.

General Hazard Precautions

These recommendations address potential hazards that are common to all installations:

Elevated Operating Temperature

The maximum rated ambient temperature for Octaire enclosures is 113° F (45° C).

All equipment should be installed in an environment compatible with the manufacturer’s maximum rated ambient temperature. In a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than the ambient room temperature.

Caution: To protect the equipment from overheating, do not operate in an area that exceeds 113° (45° C) and follow the clearance recommendation below for adequate airflow.

Airflow Restriction

Octaire enclosures are designed to adequately dissipate the heat they produce under normal operating conditions; however, this design is defeated when high heat-producing equipment is placed directly above or below an enclosure.

Caution: To prevent overheating, avoid placing high heat-producing equipment directly above or below the enclosure. The system requires a minimum of one empty rack unit above and below (three empty rack units are recommended). Verify that the openings on the sides of the enclosure are not blocked and do not have restricted air flow.

Octaire Instruction Manual

15

 

 

Page 19 Page 21
Page 20
Image 20
AMX Octaire instruction manual Installation & Setup, Site Recommendations, General Hazard Precautions
Page 19 Page 21

Octaire specifications

The AMX Octaire is a remarkable aircraft designed to meet the evolving demands of modern aviation. Renowned for its combination of advanced technology, efficiency, and versatility, the Octaire stands out in the realm of business jets and regional transport.

One of the main features of the AMX Octaire is its sleek aerodynamic design, which not only enhances aesthetics but significantly contributes to fuel efficiency. The aircraft's fuselage is built using advanced composite materials, which reduce weight while maintaining structural integrity. This results in improved performance and operational costs, making the Octaire an attractive option for companies and individuals seeking economical flying solutions.

Powered by two state-of-the-art turbofan engines, the AMX Octaire is capable of reaching an impressive cruising speed while optimizing fuel consumption. These engines are equipped with next-generation noise reduction technologies that conform to stringent environmental regulations, minimizing the aircraft's carbon footprint and contributing to sustainable aviation practices.

The cockpit of the Octaire features cutting-edge avionics, including multifunction displays and an intuitive interface for pilots. This technology enhances situational awareness and simplifies navigation, allowing for a smoother flight experience. The integration of fly-by-wire controls ensures precision handling and improved safety, making the Octaire a reliable choice for both seasoned pilots and newcomers.

Passenger comfort is a top priority in the design of the AMX Octaire. The cabin is spacious and customizable, featuring luxurious seating arrangements, modern entertainment systems, and advanced climate control. High-capacity windows provide ample natural light, creating an inviting atmosphere that enhances the onboard experience. With soundproofing materials expertly incorporated into the design, passengers can enjoy a serene environment during their journeys.

Versatility is another hallmark of the AMX Octaire. It can be adapted for various roles, including business travel, medevac missions, and cargo transport. This flexibility ensures that the Octaire can meet the needs of a diverse clientele, from corporate executives to humanitarian organizations.

In summary, the AMX Octaire is a sophisticated aircraft that embodies efficiency, comfort, and technological advancement. Its design and features position it as a leader in the aviation market, promising to deliver exceptional performance for years to come. Whether used for business or specialized operations, the Octaire is poised to redefine expectations in air travel.
Top Page Image Contents