Connectors | Analog Devices ADSP-21535 E-KIT LITE, 82-0000603-01

4.5Connectors

This section describes the function of the connectors and gives information about mating connectors. The following figure shows the locations of the connectors.

Figure 4-6: Connector Locations

ADSP-21535 EZ-KIT Lite Evaluation System Manual	4-11

Image 43

Analog Devices ADSP-21535 E-KIT LITE, 82-0000603-01 system manual Connectors, Connector Locations

Contents

ADSP-21535 EZ-KIT LITE Limited Warranty Regulatory Compliance Table of Contents Index List of Figures List of Tables Analog Devices ADSP-21535 DSP Introduction For More Information About Analog Devices Products Sdram Purpose of This Manual For Technical or Customer SupportIntended Audience Online Help Manual Contents ADSP-21535 Sharc DSP Document Name Description Getting Started Contents of your EZ-KIT Lite PackageOverview Installation Tasks PC Configuration Installing the VisualDSP++ License Installing the VisualDSP++ SoftwareInstalling the EZ-KIT Lite Debug Software EZ-KIT Lite Hardware Setup Setting Up the EZ-KIT Lite Hardware Windows 98 USB Driver Installation Installing the EZ-KIT Lite USB Driver Search for the driver Driver is located Open the .sys File Finish the Software Installation 10 Found New Hardware Wizard Windows 2000 USB Driver Installation 11 Search for a Suitable Driver 12 Locate Driver Files 13 Driver File Search Results Verifying Driver Installation 14 Completing Driver Installation Dialog Box Click on New Session Starting VisualDSP++ Using the Programmable Flag Pins Section Using the EZ-KIT Lite EZ-KIT Lite License Restrictions Start Address End Address ContentMemory Map Using Flash Memory Using the Sdram InterfaceRegister Value Function 0x2001 00FF 0x200A 0x2002 0x2000 Flag Connected Use Using the Programmable Flag Pins Example Programs Using the Power Management FeaturesUsing the Flash Programmer Utility PF14 PF13 PF12 System Architecture Section EZ-KIT Lite Hardware Reference System Architecture DSP SPORT0 Audio Interface External Bus Interface Expansion Interface Connector InterfacesJtag Emulation Port Audio Input Select Jumper JP1 Jumper and DIP Switch Settings DSP PLL Setup Switch SW2 Stereo Linein DefaultAudio Codec Disable Jumper JP2 Boot Mode Select Switch SW1 Default PLL Setup Switch Settings SW2 DSP Pin Switch Position LED and Push Button Locations LEDs and Push Buttons USB Monitor LED LED5 Power LED LED6Reset LEDs LED7, LED8 Programmable Flag LEDs LED1, LED2, LED3, LED4 Programmable Flag Push Buttons SW4, SW5, SW6, SW7 Reset Push Button SW8Push Button DSP Programmable Connector Locations Connectors Audio P5, P6 Expansion Interface P1, P2, P3Part Description Manufacturer Part Number FlashLINK P4 Jtag P8 USB P7 Specifications Power Connector P10SPORT0 P9 Resistor Voltage Plane Description Power SupplyTerminal Connection Board Current Measurements Mechanical Drawing Mechanical Dimensions Description Ref. Des Manufacturer Part Number Appendix a Bill of Materials 3V-1.0AMP Regulator CT1 DIG01 PCT3226CT-ND Tant Panasonic ECJ-2VC1H390J NPO Appendix B Schematic ADSP-21535 EZ-KIT Lite For RTC ADSP-21535 EZ-KIT Lite DSP Memory ADSP-21535 EZ-KIT Lite Audio Codec ADSP-21535 EZ-KIT Lite Config Analog ADSP-21535 EZ-KIT Lite Connectors ADSP-21535 EZ-KIT Lite Power ADSP-21535 EZ-KIT Lite Power ADSP-21535 EZ-KIT Lite Bypass Caps 4-5 Index SPORT0