Mechanical Dimensions | Analog Devices 82-0000603-01 specs

4.6.3Mechanical Dimensions

The following figure shows the location of the mounting holes as well as the PIN1 of each of the expansion connectors.

5.000
4.750
3.875			3.750		P1
3.875

2.500						P2
			1.300		1.400
1.125			1.300
1.125					P3
0.250
0.000
0.000	0.250	0.625	3.250	3.600	6.200	6.375	6.750	7.000

Figure 4-7: Mechanical Drawing

ADSP-21535 EZ-KIT Lite Evaluation System Manual	4-1

Image 48

Analog Devices 82-0000603-01, ADSP-21535 E-KIT LITE system manual Mechanical Dimensions, Mechanical Drawing

Contents

ADSP-21535 EZ-KIT LITE Limited Warranty Regulatory Compliance Table of Contents Index List of Tables List of Figures Introduction Analog Devices ADSP-21535 DSP Sdram For More Information About Analog Devices Products For Technical or Customer Support Purpose of This ManualIntended Audience Manual Contents Online Help Document Name Description ADSP-21535 Sharc DSP Contents of your EZ-KIT Lite Package Getting StartedOverview PC Configuration Installation Tasks Installing the VisualDSP++ Software Installing the VisualDSP++ LicenseInstalling the EZ-KIT Lite Debug Software Setting Up the EZ-KIT Lite Hardware EZ-KIT Lite Hardware Setup Installing the EZ-KIT Lite USB Driver Windows 98 USB Driver Installation Search for the driver Driver is located Open the .sys File Finish the Software Installation Windows 2000 USB Driver Installation 10 Found New Hardware Wizard 11 Search for a Suitable Driver 12 Locate Driver Files 13 Driver File Search Results 14 Completing Driver Installation Dialog Box Verifying Driver Installation Starting VisualDSP++ Click on New Session Using the EZ-KIT Lite Using the Programmable Flag Pins Section Start Address End Address Content EZ-KIT Lite License RestrictionsMemory Map Using the Sdram Interface Using Flash MemoryRegister Value Function 0x200A 0x2002 0x2000 0x2001 00FF Using the Programmable Flag Pins Flag Connected Use Using the Power Management Features Using the Flash Programmer UtilityPF14 PF13 PF12 Example Programs EZ-KIT Lite Hardware Reference System Architecture Section DSP System Architecture External Bus Interface SPORT0 Audio Interface Connector Interfaces Expansion InterfaceJtag Emulation Port Jumper and DIP Switch Settings Audio Input Select Jumper JP1 Stereo Linein Default Audio Codec Disable Jumper JP2Boot Mode Select Switch SW1 DSP PLL Setup Switch SW2 DSP Pin Switch Position Default PLL Setup Switch Settings SW2 LEDs and Push Buttons LED and Push Button Locations Power LED LED6 Reset LEDs LED7, LED8Programmable Flag LEDs LED1, LED2, LED3, LED4 USB Monitor LED LED5 Reset Push Button SW8 Programmable Flag Push Buttons SW4, SW5, SW6, SW7Push Button DSP Programmable Connectors Connector Locations Expansion Interface P1, P2, P3 Part Description Manufacturer Part NumberFlashLINK P4 Audio P5, P6 USB P7 Jtag P8 Power Connector P10 SpecificationsSPORT0 P9 Power Supply Terminal ConnectionBoard Current Measurements Resistor Voltage Plane Description Mechanical Dimensions Mechanical Drawing Appendix a Bill of Materials Description Ref. Des Manufacturer Part Number 3V-1.0AMP Regulator CT1 DIG01 PCT3226CT-ND Tant Panasonic ECJ-2VC1H390J NPO Appendix B Schematic ADSP-21535 EZ-KIT Lite For RTC ADSP-21535 EZ-KIT Lite DSP Memory ADSP-21535 EZ-KIT Lite Audio Codec ADSP-21535 EZ-KIT Lite Config Analog ADSP-21535 EZ-KIT Lite Connectors ADSP-21535 EZ-KIT Lite Power ADSP-21535 EZ-KIT Lite Power ADSP-21535 EZ-KIT Lite Bypass Caps Index 4-5 SPORT0