LEDs and Push Buttons | Analog Devices 82-0000603-01 manual

4.4LEDs and Push Buttons

This section describes the function of all the LEDs and push buttons. Figure 4-5shows the location of all the LEDs and push buttons.

Figure 4-5: LED and Push Button Locations

ADSP-21535 EZ-KIT Lite Evaluation System Manual	4-8

Image 40

Analog Devices 82-0000603-01, ADSP-21535 E-KIT LITE system manual LEDs and Push Buttons, LED and Push Button Locations

Contents

ADSP-21535 EZ-KIT LITE Limited Warranty Regulatory Compliance Table of Contents Index List of Tables List of Figures Introduction Analog Devices ADSP-21535 DSP Sdram For More Information About Analog Devices Products Purpose of This Manual For Technical or Customer SupportIntended Audience Manual Contents Online Help Document Name Description ADSP-21535 Sharc DSP Getting Started Contents of your EZ-KIT Lite PackageOverview PC Configuration Installation Tasks Installing the VisualDSP++ License Installing the VisualDSP++ SoftwareInstalling the EZ-KIT Lite Debug Software Setting Up the EZ-KIT Lite Hardware EZ-KIT Lite Hardware Setup Installing the EZ-KIT Lite USB Driver Windows 98 USB Driver Installation Search for the driver Driver is located Open the .sys File Finish the Software Installation Windows 2000 USB Driver Installation 10 Found New Hardware Wizard 11 Search for a Suitable Driver 12 Locate Driver Files 13 Driver File Search Results 14 Completing Driver Installation Dialog Box Verifying Driver Installation Starting VisualDSP++ Click on New Session Using the EZ-KIT Lite Using the Programmable Flag Pins Section EZ-KIT Lite License Restrictions Start Address End Address ContentMemory Map Using Flash Memory Using the Sdram InterfaceRegister Value Function 0x200A 0x2002 0x2000 0x2001 00FF Using the Programmable Flag Pins Flag Connected Use Using the Power Management Features Using the Flash Programmer UtilityPF14 PF13 PF12 Example Programs EZ-KIT Lite Hardware Reference System Architecture Section DSP System Architecture External Bus Interface SPORT0 Audio Interface Expansion Interface Connector InterfacesJtag Emulation Port Jumper and DIP Switch Settings Audio Input Select Jumper JP1 Stereo Linein Default Audio Codec Disable Jumper JP2Boot Mode Select Switch SW1 DSP PLL Setup Switch SW2 DSP Pin Switch Position Default PLL Setup Switch Settings SW2 LEDs and Push Buttons LED and Push Button Locations Power LED LED6 Reset LEDs LED7, LED8Programmable Flag LEDs LED1, LED2, LED3, LED4 USB Monitor LED LED5 Programmable Flag Push Buttons SW4, SW5, SW6, SW7 Reset Push Button SW8Push Button DSP Programmable Connectors Connector Locations Expansion Interface P1, P2, P3 Part Description Manufacturer Part NumberFlashLINK P4 Audio P5, P6 USB P7 Jtag P8 Specifications Power Connector P10SPORT0 P9 Power Supply Terminal ConnectionBoard Current Measurements Resistor Voltage Plane Description Mechanical Dimensions Mechanical Drawing Appendix a Bill of Materials Description Ref. Des Manufacturer Part Number 3V-1.0AMP Regulator CT1 DIG01 PCT3226CT-ND Tant Panasonic ECJ-2VC1H390J NPO Appendix B Schematic ADSP-21535 EZ-KIT Lite For RTC ADSP-21535 EZ-KIT Lite DSP Memory ADSP-21535 EZ-KIT Lite Audio Codec ADSP-21535 EZ-KIT Lite Config Analog ADSP-21535 EZ-KIT Lite Connectors ADSP-21535 EZ-KIT Lite Power ADSP-21535 EZ-KIT Lite Power ADSP-21535 EZ-KIT Lite Bypass Caps Index 4-5 SPORT0