Finish the Software Installation | Analog Devices 82-0000603-01

The driver installation is now complete as shown in Figure 2-9.

Figure 2-9: Finish the Software Installation

12. Click Finish to exit the wizard.

Verify the installation by following the instructions in section 2.4.6.

ADSP-21535 EZ-KIT Lite Evaluation System Manual	2-9

Image 20

Analog Devices 82-0000603-01, ADSP-21535 E-KIT LITE system manual Finish the Software Installation

Contents

ADSP-21535 EZ-KIT LITE Limited Warranty Regulatory Compliance Table of Contents Index List of Tables List of Figures Introduction Analog Devices ADSP-21535 DSP Sdram For More Information About Analog Devices Products Intended Audience For Technical or Customer SupportPurpose of This Manual Manual Contents Online Help Document Name Description ADSP-21535 Sharc DSP Overview Contents of your EZ-KIT Lite PackageGetting Started PC Configuration Installation Tasks Installing the EZ-KIT Lite Debug Software Installing the VisualDSP++ SoftwareInstalling the VisualDSP++ License Setting Up the EZ-KIT Lite Hardware EZ-KIT Lite Hardware Setup Installing the EZ-KIT Lite USB Driver Windows 98 USB Driver Installation Search for the driver Driver is located Open the .sys File Finish the Software Installation Windows 2000 USB Driver Installation 10 Found New Hardware Wizard 11 Search for a Suitable Driver 12 Locate Driver Files 13 Driver File Search Results 14 Completing Driver Installation Dialog Box Verifying Driver Installation Starting VisualDSP++ Click on New Session Using the EZ-KIT Lite Using the Programmable Flag Pins Section Memory Map Start Address End Address ContentEZ-KIT Lite License Restrictions Register Value Function Using the Sdram InterfaceUsing Flash Memory 0x200A 0x2002 0x2000 0x2001 00FF Using the Programmable Flag Pins Flag Connected Use Using the Power Management Features Using the Flash Programmer UtilityPF14 PF13 PF12 Example Programs EZ-KIT Lite Hardware Reference System Architecture Section DSP System Architecture External Bus Interface SPORT0 Audio Interface Jtag Emulation Port Connector InterfacesExpansion Interface Jumper and DIP Switch Settings Audio Input Select Jumper JP1 Stereo Linein Default Audio Codec Disable Jumper JP2Boot Mode Select Switch SW1 DSP PLL Setup Switch SW2 DSP Pin Switch Position Default PLL Setup Switch Settings SW2 LEDs and Push Buttons LED and Push Button Locations Power LED LED6 Reset LEDs LED7, LED8Programmable Flag LEDs LED1, LED2, LED3, LED4 USB Monitor LED LED5 Push Button DSP Programmable Reset Push Button SW8Programmable Flag Push Buttons SW4, SW5, SW6, SW7 Connectors Connector Locations Expansion Interface P1, P2, P3 Part Description Manufacturer Part NumberFlashLINK P4 Audio P5, P6 USB P7 Jtag P8 SPORT0 P9 Power Connector P10Specifications Power Supply Terminal ConnectionBoard Current Measurements Resistor Voltage Plane Description Mechanical Dimensions Mechanical Drawing Appendix a Bill of Materials Description Ref. Des Manufacturer Part Number 3V-1.0AMP Regulator CT1 DIG01 PCT3226CT-ND Tant Panasonic ECJ-2VC1H390J NPO Appendix B Schematic ADSP-21535 EZ-KIT Lite For RTC ADSP-21535 EZ-KIT Lite DSP Memory ADSP-21535 EZ-KIT Lite Audio Codec ADSP-21535 EZ-KIT Lite Config Analog ADSP-21535 EZ-KIT Lite Connectors ADSP-21535 EZ-KIT Lite Power ADSP-21535 EZ-KIT Lite Power ADSP-21535 EZ-KIT Lite Bypass Caps Index 4-5 SPORT0