Manuals / AT&T / Communications / Telephone

AT&T 944 user manual Wall Installation

Models: 944

1 43

Download 43 pages 44.01 Kb

Page 9

INSTALLATION

3Connect the handset cord.

Plug one end of the coiled handset cord into the jack on the left side of the phone. Plug the other end into the handset, and hang up.

4Connect the power adapter.

Use only the power adapter provided with this product. To obtain a replacement, call 1 800 222–3111.

Plug one end of the power adapter into the jack labeled POWER on the back of the phone. Plug the other end into a standard electrical outlet not controlled by a wall switch.

NOTE: The screen will display POWERFAIL the first time you plug in the phone. Press any key to clear the screen.

5Check for dial tone.

Lift the handset and listen for a dial tone. If you cannot hear a dial tone, turn to IN CASE OF DIFFICULTY.

6Initialization.

As soon as you connect the power cord, the phone runs a quick self-test and the screen displays Initializing.. for about seven seconds. When the test is complete, the phone enters an initial setup mode and the screen displays press PROG to setup your phone. See FEATURE SET UP beginning on page 13.

NOTE: The phone will run through this same initialization anytime it is reconnected to AC power (i.e., after a power failure or when the unit has been unplugged).

Wall Installation

1Reverse the handset tab.

Hold down the switchhook, then pull the tab out and rotate it 180 degrees. Push the tab down into the grooves so it settles into position.

8

Image 9

AT&T 944 user manual Wall Installation

Contents

Part 1 Important Product Information Four-Line Intercom SpeakerphoneContents Before YOU Begin Glossary Feature Function Setting Options Features ListWhen you hear It means Audible SignalsInstallation Table/Desk InstallationInstall one 9V battery Two Two-Line Jacks Connect the telephone line cords to the telephoneWall Installation Install one 9V battery Mount the phone on the wall Connect the power adapter to the telephoneTwo Two-Line Jacks Convenience Ports Feature Options Feature SET UPSet the Time/Date Assign an Extension Number to Your PhoneTurn the Ringer On or Off for Each Line Set Delay Ring Select the Ringer TypeTurn Line Usage On or Off for Each Line Assign the Prime Line Line Preference Assign the Line Group for this PhoneTurn Auto-Mute On or Off Set the Dial Mode Set Audio ModeSet the Flash Time Turn Hold Reminder On or OffProgram the Centrex Console Delayed Ring Time Erase All Settings and Return the Phone to Default SettingsSet Your Phone to be the Centrex Console Phone Telephone Operation Making or Answering a Call Telephone OperationHandset SpeakerphoneTimer Switching ModesPause Call Privacy Canceling Call PrivacyDo Not Disturb Restoring Call PrivacyVolume Line-in-Use LightsRedial Auto Redial Switch Between LinesHold Speakerphone or HeadsetFlash MuteTemporary Tone Dialing Conference CallsTransfer a Call Low Battery IndicatorTo talk privately with one party To drop one lineSpeed Dial Operation Storing a Number in a Speed Dial Location Reviewing a Speed Dial EntryMaking a Speed Dial Call Intercom Operation Making an Intercom Call with the Handset Basic Intercom OperationsMaking an Intercom Call with the Speakerphone or Headset Switching Between an Intercom Call and a Single-phoneAnswering an Intercom Call Making a Single-phoneAnswering a System-wide Paging All PhonesMaking an Intercom Conference Call Room MonitorAdding a FAX Machine Using a Fax SwitchLine Lights Remain On When No Line is Connected Intercom Paging Signal Not ReceivedCase of Difficulty Telephone Does Not RingTone Signals Do Not Activate a Remote Device Operation During a Power FailureDisplay Screen is Blank Line Groups Expanding the Phone SystemPrivate Lines Centrex Operation Setup ChecklistEnabling the Console Phone Console OperationSetting Ring Delay Duration Answering a Delayed RingPicking Up Another Station’s Line Index Audio Mode 4Reset ALL Advanced American Telephones. All rights reserved