Atmel ATA6264 - page 16

16

4929B–AUTO–01/07

ATA6264 [Preliminary]

Figure 5-4. Start-Up and Power-Down Procedure if VVCORE Programmed to Be 5V or 2.5V

5.3.3 Start-up Procedure if VVCORE Programmed to Be 1.88V

Phase1: After switching on the ignition key, the K15 voltage will appear at pin K15. If, in addi-

tion, the voltage at pin K30 is larger than 3.85V to 5V, the EVZ regulator will be enabled. The

signal K15GOOD can be replaced by the serial interface command KEYLATCH which can be

set by the serial interface.

Phase2: If VEVZ is larger than 7.5V to 9V, the VSAT regulator starts operating.

Phase3: After VVSAT has reached 6.77V to 7.2V, the VPERI regulator starts working.

Phase4: If VVPERI is higher than 1.25V to 1.7V, the VCORE regulator will be enabled.

t

VK30

3V to 4.15V3V to 4.15V

5.5V to 6.2V

too low EVZ voltage

VSAT goes into On Mode

charge pump deactivated

6.77V to 7.2V 7V to 6.27V

7.5V to 9V

VGEVZ

VEVZ

VVSAT

VK15

VVCORE

VVPERI

t

t

t

t

t

t

Threshold to enable

VCORE regulator

Threshold to start

VCORE regulator

Contents

Main Features 1. Description Airbag Power Supply IC ATA6264 Preliminary ATA6264 [Preliminary] Figure 1-1. Block Diagram V VSAT V 1.1 Block Description ATA6264 [Preliminary] 2. Pin Configuration Figure 2-1. Pinning QFP44 Table 2-1. Pin Description ATA6264 [Preliminary] 3. Absolute Maximum Ratings 3. Absolute Maximum Ratings (Continued) 4. Functional Range 4.1 Protection Against Substrate Currents 5. Supply Currents 5.1 Discharger Circuit 5.2 Initial Programming of the ATA6264 Page Page 4929BAUTO01/07 5.3 Start-up and Power-down Procedure V V V V Page Page Page 6. Power Supply Sequencing Figure 6-2. Block Diagram Power Supply Sequencing V V V VCORE - Regulator V 7. Charge Pump VEVZ = 5.5V to 40V or VK30 = 5.5V to 40V, VK15 > 3V, VVINT = 3.7V to 5.47V VVSAT, VVPERI and VVCORE are within functional range limits, Tj = 40C to 150C Table 7-1. Electrical Characteristics Charge Pump 8. GKEY Function Figure 8-2. Application With High Current Switch (GKEY Function Not Used) VK15 = 3V to 40V, VK30 = 3.85V to 40V VEVZ, VSAT, VPERI and VCORE are within functional range limits, Tj = 40C to 150C Table 8-2. Electrical Characteristics GKEY Function 9. EVZ Step-up Regulator Page ATA6264 [Preliminary] VK15 = 3V to 40V, VK30 = 5V to 40V, CGEVZ = 200 pF to 2 nF, VINT = 3.7V to 5.47V VSAT, VPERI and VCORE are within functional range limits, Tj = 40C to 150C Table 9-1. Electrical Characteristics EVZ Step-up Regulator Table 9-1. Electrical Characteristics (Continued) EVZ Step-up Regulator Table 9-1. Electrical Characteristics (Continued)EVZ Step-up Regulator 10. VSAT Power Supply VEVZ = 5.5V to 40V, VCP > VEVZ + 7V, VINT = 3.7V to 5.45V VK30, VPERI and VCORE are within functional range limits, Tj = 40C to +150C Table 10-1. Electrical Characteristics VSAT Power Supply Table 10-1. Electrical Characteristics (Continued) VSAT Power Supply 11. VPERI Power Supply VSAT > 7.5V, VINT = 3.7V to 5.47V, VCORE < VPERI + 0.3V VK30, VEVZ and VCORE are within functional range limits, Tj = 40C to 150C Table 11-1. Electrical Characteristics VPERI Power Supply 12. VCORE Power Supply VEVZ = 5.5V to 40V or VK30 = 5.5V to 40V, VCP > VEVZ + 7V or VCP > VK30 + 7V, VPERI >V VSAT is within functional range limits, Tj = 40C to 150C Table 12-1. Electrical Characteristics VCORE Power Supply Page Table 12-1. Electrical Characteristics (Continued) VCORE Power Supply 13. USP Comparator for General Purpose 14. Reference Voltage and Reference Current Generation 15. Reset Function (Pin RESQ and Pin RESQ2) Figure 15-2. Functional Principle of RESQ, RESQ2 Page Figure 15-4. Application Example VEVZ = 5.5V to 40V, VPERI = 1V to 5.5V, VINT = 3.7V to 5.47V VK30, VSAT, and VCORE are within functional range limits, Tj = 40C to 150C Table 15-1. Reset Truth Table Table 15-2. Electrical Characteristics Reset Function (Pin RESQ and Pin RESQ2) Table 15-2. Electrical Characteristics (Continued) Reset Function (Pin RESQ and Pin RESQ2) 16. Watchdog Function Page Page Figure 16-4. Watchdog Trigger Functional Principle (Unsuccessful Watchdog Trigger) Page VPERI > Reset threshold, VCORE > Reset threshold VK30, VEVZ and VVSAT are within functional range limits, Tj = 40C to 150C Table 16-2. Electrical Characteristics Watchdog Function Figure 16-5. Watchdog Trigger 17. LIN/ISO 9141 Interfaces Table 17-1. Electrical Characteristics LIN/ISO 9141 Interfaces Table 17-1. Electrical Characteristics (Continued)LIN/ISO 9141 Interfaces Figure 17-2. Timing LIN/ISO 9141 Interface Table 17-1. Electrical Characteristics (Continued)LIN/ISO 9141 Interfaces 18. Voltage/Current Sources (IASGx Sources) Figure 18-1. Functional Principle of the IASG Interface - VK30 and VVSAT are within functional range limits, Tj = 40C to 150C As defined in Section 4. Functional Range on page 8, CIASGx 10 nF and 825RISENS 5k + Table 18-1. Electrical Characteristics Voltage/Current Sources (IASGx Sources) Table 18-1. Electrical Characteristics (Continued)Voltage/Current Sources (IASGx Sources) ATA6264 [Preliminary] 19. AMUX (Analog Multiplexer for Voltage Measurements) Table 19-1. Electrical Characteristics AMUX (Analog Multiplexer for Voltage Measurements) ATA6264 [Preliminary] 20. UZP Buffer Table 20-1. Electrical Characteristics UZP Buffer 21. Chip Temperature Measurement 22. Serial Interface Commands 22.1 Overview Table 22-1. Electrical Characteristics (Continued) SerialInterface Commands Figure 22-1. Timing Serial Interface 22.2 Set Commands #16#1 Table 22-2. Set of Serial Interface Commands Table 22-3. Key Latch Commands Table 22-4. Watchdog Commands Table 22-5. Switch Commands Table 22-6. Initial Programming (IP Command) Table 22-7. Diagnosis Commands Page 22.3 Serial Interface Status Register Table 22-11. Information Provided by the Itemized Bits of the Status Register Page 23. Test Mode 24. Application Circuits Figure 24-1. Overview of a Typical Airbag System 4929BAUTO01/07 Figure 24-2. Typical Application Circuit ATA6264 26. Package Information 25. Ordering Information Page 28. Table of Contents Page Atmel Corporation Atmel Operations Regional Headquarters Europe Asia Japan