Manuals / Barco / Computer Equipment / Projector

Barco R9001960 Hardwired Remote Input, Directly to one of the IR sensors of the projector

Models: R9001960

1 127

Download 127 pages 10.86 Kb

Page 37

Image 37

4. Getting Started

Hardwired Remote Input

1.Plug one end of the remote cable in the connector on the bottom of the RCU.

2.Plug the other end in the connector in the front panel of the projector labelled RC. (image 4-7)

Image 4-7

Wired RCU connection to the projector

Directly to one of the IR sensors of the projector.

When using the wireless remote control, make sure you are within the effective operating distance (30m, 100ft in a straight line). The remote control unit will not function properly if strong light strikes the sensor window or if there are obstacles between the remote control unit and the projector IR sensor.

Image 4-8

RCU directly to the IR sensor

R5976182 BARCOREALITY 6500 30012001

Page 37

Image 37

Barco R9001960 owner manual Hardwired Remote Input, Directly to one of the IR sensors of the projector, Getting Started

Contents

BARCOREALITY R9001960 R9001969INTELLIGENT DISPLAYS OWNER’S MANUALPrinted in Belgium Changes CopyrightTrademarks Federal Communication Commision FCC StatementPage Table of contents TABLE OF CONTENTS1. Packaging and Dimensions 2. Installation GuidelinesTable of contents 9. Service modeD. Cleaning the Dustfilter A. Standard Source Set Up FilesC. Source Numbers 81 - 86 and 91 - 96 Table of contentsR5976182 BARCOREALITY 6500 Table of contents1.1 Box content 1. PACKAGING AND DIMENSIONS1. Packaging and Dimensions ContentDimensions overview 1.4 Dimensions1.3 Lens Packaging 1. Packaging and DimensionsImage Side view dimensions projector Image 1. Packaging and DimensionsTop view dimensions projector R5976182 BARCOREALITY 6500 1. Packaging and Dimensions2.1 Installation guidelines 2. INSTALLATION GUIDELINES2. Installation Guidelines Ambient Temperature ConditionsWhich configuration can be used ? 2.2 ConfigurationWhich screen type ? What image size ? How big should the image be ?2. Installation Guidelines 2.3 LensesOverview 2.3.1 Lenses Available lenses 2.3.2 Lens selection How to select ?2.3.3 Lens formulas Formulas Lenses2.3.5 Cleaning the lens 2.3.4 Lens installation How to install ?The procedure for the mounting of a Scheimpflug lens is different Refer to the installation manual of the lens2.4.1 Battery installation How to install the battery How to clean the lens ?2.4.2 Battery replacement How to replace the batteries in the RCU Other lenses can also be cleaned safely with this TorayseeTM clothNote, only important if more than one projector is installed in the room 2. Installation GuidelinesR5976182 BARCOREALITY 6500 2. Installation Guidelines3.2 Switching on 3.1 Power connectionAC Power cord connection How to switch on3. Connections Lamp run time indication while running3.4 Switching off 3.3 Switching to standbyHow to switch to standby? How to switch off the projector?3.5.3 5-cable input Where to find ? Set up of the input selectionWhich signals can be connected to the 5 cable input Connector nameConfiguring the 5-cable input How to select slotPossible indications on the input slot menu Audio ConnectionPin configuration of the D15 connector How to connect the computer to the input?3.5.4 Computer input/Monitor output 3.5.5 Video inputHow to connect the S-Video signal How to connect a Video sourcePin configuration of the mini DIN plug How to select slot 4?How to connect ? How to connect a SDI source ?How to select slot 6? 3.6 Communication connections3.6.2 Communication with peripherals Configuration of the port Set up of the Baud rate for communicationWhat is possible with an RCVDS05 connected 3.6.3 Mouse When available ?What is available ? How to activate ?How to lock an audio input ? Before switching off, disconnect first the mouse cable4. GETTING STARTED Remote control functions4.1 RCU & Local keypad 4.2 Terminology overview4. Getting Started the projector will restart4.3 Operating the projector 4.3.1 Switching on How to switch on4. Getting Started Starting image projectionLamp run time indication while running 4. Getting Started4.3.2 Switching to standby How to switch to standby? 4.4 Quick Set Up Adjustments4.3.3 Switching off How to switch off the projector? 4.4.1 Quick lens Adjustment Quick zoom/focus adjustmentHow to change ? 4.5 Using the RCUPointing to the reflective screen 4. Getting StartedDirectly to one of the IR sensors of the projector Hardwired Remote InputImage Wired RCU connection to the projector 4. Getting StartedSet up an individual Projector Address Why a projector address ?4.6 Projector Address 4.6.1 Controlling the projector4.7 Controlling the projector How to Program an Address into the RCU?Input Selection Picture ControlsThe Selection key The Pause Key4. Getting Started How to set up? 5.2 Start up auto powerSet up the auto power mode 5. START UP MODER5976182 BARCOREALITY 6500 5. Start Up mode6.2 Adjust 6. AUTO IMAGE ADJUSTMENT6. Auto Image Adjustment Why auto image ?Set up When is it disabled ?6.3 Action 6. Auto Image Adjustment7. Random Access 7. RANDOM ACCESS7.1 overview flow Overview7.2.2 Possible file manipulations Connecting a new source 7.2 Picture ServicesStart up 7.2.1 File annotation How a file is built upPossible file Manipulations 7.2.3 Start up of file services Start up7.2.4 Load file Start up Load file 7. Random AccessHow to load a file ? Changing the filter settingThe image is not perfect ? 7.2.5 Edit file7.2.5.2. Changing the settings Different methods 7.2.5.1. Start up How to start up the Edit menu ?How to change a setting with the numeric keys? How to change a setting with the cursor keys?7. Random Access How to find the correct values for the item in the Edit file menu?EDIT FILE OPTIONS Image Example for Clamp position trailing 7. Random AccessChanging the characters 7.2.6 Rename Start Up7. Random Access 7. Random Access 7.2.7 Copy Start UpChanging the characters 7.2.8 Delete Start up and delete 7.3 Picture Tuning7.2.9 File options Start up File Sort7.3.3 Color Temperature Available Color temperatures Changing the CTI setting7.3.1 Start up Start up 7.3.2 CTI7.3.4 Gamma What can be adjusted ? Adjusting the color balanceDecoding is only for NTSC signals Start Up7.3.6 Dynamic Color Depth Purpose How to change the decoding setting ?Changing the Dynamic Color depth value 7.3.7 Noise Reduction PurposeBlack balance adjustment 7.3.8 Input Balance Why adjusting the input balance?Changing the noise reduction value Step to be takenWhite balance adjustment 7.4 Audio Tuning7.4.2 Volume, Balance, Bass and Treble How to adjust ? 7.4.1 Start up StartupHow to set up the fade ? How to stop sound reproduction ?7.4.3 Mute Purpose 7.4.4 Fade PurposeHow to lock the input source to an audio source? How to set up the sound mode?7.5 Geometry 7.4.6 Video - audio lock PurposeNote The default value for the shift is How to shift the image ?7.5.2 Geometry start up Start up 7.5.3 Shift What can be done ?Which blanking adjustments are available ? Size adjustment7.5.5 Side Keystone What can be done ? Aligning the keystoneHow to set up the desired aspect ratio ? Adjusting the blanking7.5.8 Options What is possible ? 7.5.7 Aspect Ratio Purpose7.6 IEEE Set up of the geometry options7.6.1 Starting up the controls Purpose of the IEEE 1394 controls 7.6.2 IEEE 1394 Control OverviewHow to toggle? 7.6.2.2. IEEE 1394 Setup Purpose7.6.2.1. Start up Start up 7.6.2.3. Audiodecoding Purpose7.6.3 Camcorder Control Purpose How to select a function ?Avalilable functions 7. Random AccessR5976182 BARCOREALITY 6500 7. Random Access8.2 Start up installation mode 8. INSTALLATION MODE8. Installation mode Build-up of the installation modeTo view or the change the input configuration 8.4 No SignalWhat if a switcher is connected to the projector ? no valid signal connected to the input8.4.2 Changing the shutdown setting How to change ? 8.4.1 Changing the background color How to change ?8.4.3 Changing the Shutdown time Range 8. Installation modeZoom/Focus adjustment of the lens 8.5 Lens adjustment8. Installation mode How to change ?How to change the position? Shift adjustment of the lens8.6 Text Box Position What can be done with the text box?8.7.1 What are Quick Access Keys? What can be done with these keys? 8.7 Quick Access Keys8.7.3 Programming the Quick Access Keys How to program? 8.8 Start Up mode8.8.1 Start up with identification screen How to set up? 8.9 Network Configuration8.8.2 Start up auto power Set up the auto power mode DHCP8.10 800 peripheral Set up the network configurationEntering the necessary addresses 8.10.1 Defining the Output module of the RCVDS05Defining the output module 8.11 Configuration8.10.2 Defining the Infrared Communication protocol Which protocols are available?How to change this color setting? Set up the Correct ConfigurationFor more information, see Configuration, page 8.12 OSD ColorHow to select an internal patterns? 8.14 Switching ModeWhat can be set up with the switching mode? How to install the switching mode?8.15 Shutter How to activate the shutter?What should be done? 8. Installation mode9. Service mode 9. SERVICE MODE9.1 Build-up 9.2 Start upHow to enable or disable the password function ? 9.4 Change PasswordHow to change the password ? 9. Service mode9.6 Change Projector Address 9.5 Change LanguageWhat can be changed? 9.6.1 Start up Start upHow to enter the new projector address? 9.6.2 Projector Address How to change the projector address?9.6.3 Common Address How to change a common address? Entering the new common addressWhen is it allowed? 9.8 Reset Lamp Runtime9.7 Change Baudrate PC 9.9 Lamp Run time History9.10 Lamp Dimming A projector starts always with full lamp power9.11 BARCO Logo 9. Service modeHow to add the BARCO logo or to change the setting? 9.12 Panel AdjustmentsAvailable Settings 9. Service mode9.13 Uniformity 9.14 Preset Input Balance9.15 I2C Diagnoses 9. Service mode9. Service mode How to start up the I2C diagnoses?SERVICE I2C DIAGNOSISR5976182 BARCOREALITY 6500 9. Service modeA. Standard Source Set Up Files A. STANDARD SOURCE SET UP FILESA.1 Table overview Table overviewName A. Standard Source Set Up FilesResolu FvertPtot6 Name1Pact7 Ltot8R5976182 BARCOREALITY 6500 A. Standard Source Set Up FilesB.1 General requirements B. BARCO CONTROL MANAGERB.2 About the control manager B. BARCO Control ManagerInformation on the Start Up page B.3 Control manager Start PageStarting up B. BARCO Control ManagerB.4 Control Using the default windowB. BARCO Control Manager OverviewAvailable items B.4.1 Start up Start upB. BARCO Control Manager Image B-4 Control start up screenB.4.2 General Control What can be done SecurityOverview of possible adjustments B. BARCO Control ManagerB.4.3 Source How to select How to selectB. BARCO Control Manager Image B-6 General control screenB. BARCO Control Manager B.4.4 Image Settings How to changeImage B-8 B.4.6 Lens adjustment How to change What is decodingClick on init to return to the default value CTI B.4.5 Image Enhancement Changing noise reduction & dynamic colorImage B-10 Lens adjustment B.4.7 Geometry adjustment What can be adjustedImage B-11 Geometry adjustment B. BARCO Control ManagerVertical Size adjustment Shift adjustmentHorizontal Size adjustment Keystone adjustmentTo return to the default position, click on Reset How to adjustImage B-12 Blanking adjustment B. BARCO Control ManagerB.4.9 Audio Adjustment How to adjust B.5 ConfigurationClick on init to return to the default value B. BARCO Control ManagerB.5.1 Start up Start up B.5.2 Mail Set up What can be doneAvialable items B. BARCO Control ManagerB.5.3 Security What can be done Repeat the above steps for the other mail configurations if necessarySet up Image B-15 Mail configurationChanging the administrator password Set up of the advanced user passwordB.5.4 Data & Time TCP/IPSet up B.5.5 Settings What can be doneImage B-17 Date & time setup screen B. BARCO Control ManagerProjector location set up Projector name set upIP address SMPT server set up B.5.6 Source What can be doneHow to fill out B.6 DiagnosticsImage B-19 Source set up screen B. BARCO Control ManagerB.6.1 Start Up Start Up B.6.2 General Status What is availableB.6.3 Job Log Overview B. BARCO Control ManagerImage B-22 Advanced diagnostics screen B.6.4 Advanced Diagnostics OverviewB. BARCO Control Manager Image B-21 Job log screenC. SOURCE NUMBERS 81 - 86 AND How to create a second source?C.1 Projector without any 800 peripheral connected C.2 Projector with a 800 peripheral connectedC. Source Numbers 81 - 86 and 91 C.2.2 Source numbers 81 OverviewD.1 Cleaning D. CLEANING THE DUSTFILTERD. Cleaning the Dustfilter When should it be done?R5976182 BARCOREALITY 6500 D. Cleaning the DustfilterGlossary GLOSSARYDomain httpR5976182 BARCOREALITY 6500 GlossaryINDEX Numerics/SymbolsIndex Index Ambient Temperature57-60 identification79-80 Indexdimming R5976182 BARCOREALITY 6500 IndexList of tables LIST OF TABLESR5976182 BARCOREALITY 6500 List of tablesList of images LIST OF IMAGES